gefran ADL500 Quick Start Up Manual, Specification And Installation Download Page 2

Page: 2 / 96

ADL500 • Quick installation guide - Specifications and connection

Information about this manual

The ADL500 HW+QS (Hardware and Quick start guide) is a handy-sized manual for mechanical installation, electrical

connection and fast start-up.

The manual of functions and parameter descriptions (ADL500 SW) can be found on the Gefran website, Downloads

section (https://www.gefran.com/en/products/642-adl500-lift-field-oriented-vector-inverter-for-synchronous-asynchro

nous-motors).

Software version

This manual is updated according to:

- software version V 1.0.2

- Lift application, EFC V 1.8.0

The identification number of the software version

can be read in the datamatrix (see section 2.3 of this manual) or on

parameter PAR 174

Firmware Version (

DRIVE INFO menu).

General information

Note !

In industry, the terms “Inverter”, “Regulator” and “Drive” are sometimes interchanged. In this document, the term “Drive” will be used.

Before using the product, read the safety instruction section carefully. Keep the manual in a safe place and available to

engineering and installation personnel during the product functioning period.

Gefran Drives and Motion S.r.l. has the right to modify products, data and dimensions without notice. The data can only

be used for the product description and they can not be understood as legally stated properties.

Thank you for choosing this Gefran product.

We will be glad to receive any possible information which could help us improvingthis manual. The e-mail address is

the following: [email protected].

Summary of Contents for ADL500

































































































Search results

Summary of Contents for ADL500

Reviews:

gefran ADL500, Quick Start Up Manual, Specification And Installation, Page: 2 / 96

Search results

Summary of Contents for ADL500

Reviews: