GEFRAN SpA
Via Sebina, 74 - 25050 PROVAGLIO D’ISEO (BS) ITALY
Note
Change all menu parameters by
using the front panel buttons
GETTING STARTED
• Unpack Contents
• Verify model numberand application
• Power Controller
• Program for yourapplication
Program Your Gefran Controller
2
* Parameter may be left at default value for input types 0...37
Input Sensor
Sensor Type
Sensor Type
0 TC J °C
30 PT100 °C
1 TC J °F
31 PT100 °F
2 TC K °C
32 JPT100 °C
3 TC K °F
33 JPT100 °F
4 TC R °C
34 PTC °C
5 TC R °F
35 PTC °F
6 TC S °C
36 NTC °C
7 TC S °F
37 NTC °F
8 TC T °C
44 4...20 mA
9 TC T °F
46 0...10 V
Connect Your Controller
3
What’s Included
• 48x96 DIN 1200-RDR0-00-0-x
Gefran Controller x2
• Mounting Bracket
• Panel Sealing Gasket
• Screw Terminal Cover
• Multi-Language Manual
1
• Press and hold
F
until
PAS
appears —
ENTER
99
• Press
F
once,
Pro
appears —
ENTER
128
• Press
F
once,
PAS
appears —
ENTER
99
• Press and hold
F
until
Hrd
appears
• Press
F
twice,
Ctr
appears —
ENTER
14
• Press
F
twice,
but
appears —
ENTER
1
• Press and hold
F
until
CFG
appears
• Press and hold
F
until
C.Me
appears
—
ENTER
0
cooling with Air
—
ENTER
1
cooling with Oil
—
ENTER
0
cooling with Water
• Press and hold
F
until
1 nP
appears
• Press
F
twice,
tYP
appears —
ENTER
the Input Sensor number from the list
• Press
F
repeatedly until
Lo.S
* appears —
ENTER
the minimum Input Scale limit
• Press
F
once,
H i.S
* appears —
ENTER
the maximum Input Scale limit
• Press
F
repeatedly until
Lo.L
* appears —
ENTER
the minimum Alarm Scale limit
• Press
F
once,
H i.L
* appears —
ENTER
the maximum Alarm Scale limit
• Press and hold
F
until
Out
appears
• Press
F
three times,
rl.1
appears —
ENTER
1
• Press
F
twice,
rl.3
appears —
ENTER
2
• Press and hold
F
until you return to the main process display. This is the display after
PAS
and will be indicated by the Process Variable if an input sensor is connected, or
Lo
,
H i
,
Sbr
,
Err
if no input is connected.
• Use the and buttons to adjust the control setpoint (SV) from the main display.
• Press
F
once from the main display,
AL.1
appears to adjust the Alarm 1 setpoint.
• Press the
button to switch between automatic and manual control modes from the
main display. LED 1(
L1
) will light while in manual mode.
POWER
This Quick Start Guide provides basic information on
setting up the Gefran 1200 controller for the application
referenced above. Additional software and hardware
configuration information can be found in the User’s Manual
included with this controller or online at www.gefran.com
If needed, automatic tuning (Self-Tune) can be enabled
with the following steps
• Press and hold
F
until
CFG
appears
• Press
F
once,
S.Tu
appears —
ENTER
2
• Press
F
once
• Cycle power to the controller
• LED 3 (
L3
) will flash during the tuning process
With the machine at ambient temperature and
the control setpoint (SV) set...
Self-Tune will automatically save new PID
values once complete
Additional wiring
configurations are
available in the User’s
Manual and General
Setup Guide
Quick Start Guide
12
13
11
10
ALARM
+
-
1
2
1
2
+
-
1
2
1200-RDR0-00-0-x
Programmable PID Controller
Heat - Cool - Alarm
COOLING
HEATER
POWER CONTROL
THERMOCOUPLE
