Gefen GTB-HD4K2K-848-BLK User Manual Download Page 20

Page: 20 / 146

page | 8

Connection Instructions

►

Video

1. Use HDMI cables to connect up to eight 4K Ultra HD sources to the input ports

(

In 1

In 8

) on the matrix.

2. Connect up to eight 4K Ultra HD displays using the output ports (

Out A

Out H)

on the matrix.

►

Ethernet

3. Connect a CAT-5e (or better) cable from the

IP Control

port on the matrix to a Local

Area Network (LAN).

►

RS-232

4. Connect an RS-232 cable from the

RS-232

port on the matrix to the RS-232 connector

on the automation controller.

►

5. Connect an IR extender (Gefen part no. EXT-RMT-EXTIRN) to the

IR Ext

port

on the matrix.

►

Power

6. Connect the included power supply to the

24V DC

power receptacle on the matrix.

7. Connect the power cord to an available electrical outlet.

Installation

tting S

tar

ted

tting S

tar

ted

Summary of Contents for GTB-HD4K2K-848-BLK



















































































































































Search results

Summary of Contents for GTB-HD4K2K-848-BLK

Reviews:

Brands by name

Popular brands

Gefen GTB-HD4K2K-848-BLK, User Manual

Search results

Summary of Contents for GTB-HD4K2K-848-BLK

Reviews:

Brands by name

Popular brands