background image

USER MANUAL G-913-P01

 

PAGE  

3

 

PPUH „GECO” Sp. z o.o.                                   ISSUE  I 

AS OF 2018.09.13

 

1

 

GENERAL CHARACTERISTICS  

Independent Temperature Controller 

called further 

G913 

is a modern, comfortable and easy to 

operate appliance. It was produced using microprocessor technology and automatic surface 
assembly.  
 
 

This device registers measurements from two temperature sensors connected directly to it. 

The recorder is designed for independent work. 
The operating mode depends on the settings made by the manufacturer. 
 

Temperature recorder G-913-P01 was equipped with: 

 

built-in memory allowing for recording of measured temperatures

  

 

USB  interface  allowing  to  read  stored  temperature  values

terfejs  USB  pozwalający  odczytać 

zapisane wartości temperatury 

 

 

 

ALWAYS DISCONNECT THE RECORDER FROM POWER DURING 

THUNDERSTORMS 

 

 

 

The recorder does not require any special maintenance. The keyboard was made from a special 

type of foil resistant to high temperature and most chemicals. It is not permitted to clean it with 
sharp objects. It is sufficient to clean the front plate with a wet cloth from time to time. 

 

2

 

DESCRIPTION OF THE RECORDER PANEL 

A diode that signals 
recording, operation of USB 
storage and alarm states

 

USB 2.0 connector to 
support USB storage 

Summary of Contents for G-913-P00













Reviews: