manualshive.com logo in svg

Gechter 2,5 HKPE, Translation Of The Original Operating Manual, Page: 49 / 60

Share
Download
Gechter 2,5 HKPE Translation Of The Original Operating Manual Download Page 49

 

 

Service and maintenance 

 

9

 

 

Hand toggle presses 

– 

Translation of the original operating manual 

 

44 

 

9.2

 

Technical Support 

 

 

 

The following maintenance instructions are only intended as rec-
ommendations by the manufacturer!  

The press operator is required to document maintenance-related 
observations  and  to  expand  and  specify  the  maintenance  in-
structions in this operating manual accordingly!  

The maintenance instructions for purchased parts are also to be 
observed! 

 

 
The following sections describe the maintenance work required for optimal and 
fault-free device operation. 
 
If increased wear is identified during regular checks, the required maintenance 
intervals are to be shortened according to the actual signs of wear.  
 
Please contact the company GECHTER Werkzeug- und Maschinenbau GmbH for 
questions about maintenance work and intervals. 
 

 

Please refer to the "Identification" chapter for how to contact the custom-
er service of  
Gechter GmbH! 

 

 

 

Observe the following specified time intervals for inspection and maintenance: 
 

Interval 

Maintenance work 

Personnel 

if necessary 

Press

: clean

  

Press carriage

:

 Lubricate the prism guide

 

 

Operator 

Daily 

Press carriage

:

 Lubricate the prism guide (slid-

ing guide oil Shell T 68 or equivalent)  

Technically 
trained person-
nel 

 

 

 

National  laws  or  provisions  of  more  frequent  inspection  and/or 
maintenance of the device are to be observed. 

Summary of Contents for 2,5 HKPE





























































Reviews:

No comments