Gechter 2,5 HKPE Translation Of The Original Operating Manual Download Page 34 | Manualshive

Page: 34 / 60

background image

Commissioning / Operation

6

Hand toggle presses

–

Translation of the original operating manual

29

6.2

Operation

Crushing and hand injuries

Ensure that no body parts enter into the tool area during opera-
tion!

Risk of injury from material dust!

Dust  that  makes  its  way  into  the  airways  or  eyes  when  pro-
cessing metal powder or similar may lead to injuries.

Always use an exhaust system during powder processing.

Never work without a respirator mask during powder processing.

Never work without a protective goggles during powder pro-
cessing.

6.2.1

Press process work steps

Due to the number of application possibilities of the hand toggle
press, detailed work steps cannot be described. The respective
work steps must be specified by the operator.

The following work steps describe a simplified pressing process in order to il-
lustrate the general pressing process:



Take the workpiece from the stock.



Place the workpiece in the press tool.



Execute the approach stroke of the upper die with the hand lever.



Remove the workpiece from the pressing tool and place to the side.

«
...
32
33
34
35
36
...
»

Summary of Contents for 2,5 HKPE





























































Reviews:

No comments

Related manuals for 2,5 HKPE

Brand: Gallagher Pages: 82

Brand: Gallagher Pages: 40

Brand: Daxten Pages: 2

Brand: Far Tools Pages: 33

Brand: KEB Pages: 46

Brand: Toku Pages: 7

Brand: Elk Products Pages: 2

Brand: jbc Pages: 72

Brand: TE Connectivity Pages: 4

Brand: HIKOKI Pages: 16

Brand: Eastwood Pages: 12

Brand: Master Appliance Pages: 2

ROTO-TIGER RT-2000

Brand: Airtec Pages: 87

Brand: Lambda Electronics Pages: 22

Brand: Clam Pages: 4

Brand: Xantrex Pages: 62

Brand: Qonnect Pages: 4

Brand: KMB Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands