background image

The signs relating to the valve must always be complete and legible. Check,
clean and replace the signs as necessary at regular intervals.

Observe the Technical Data specified and the limits of use!

Hint!

Carry out regular checks. This way you can ensure that these
measures are actually observed.

2.3

Subsequent changes

You should never make any technical modifications to the valve. Otherwise you
will have to undergo a new conformity process in accordance with the EC
Machinery Directive on your own.
In general, only original spare parts supplied by GEA Tuchenhagen GmbH
should be fitted. This ensures the reliable and economical operation of the valve.

2.4

General safety instructions and dangers

The valve is operationally reliable. It was built according to state-of-the-art
science and technology.
Nevertheless, the valve can pose dangers, especially if

the valve is not used in accordance with its intended use,

the valve is not used correctly,

the valve is operated under impermissible operating conditions.

2.4.1

Principles for safe operation

Dangerous situations during operation can be avoided by safety-conscious and
proactive behaviour of the staff.
To ensure safe operation of the valve the following principles apply:

The Operating Instructions must be kept ready to hand at the valve's place of
use. They must be complete and in clearly legible form.

Only use the valve for its intended use.

The valve must be functional and in good working order. Check the condition
of the valve before starting work and at regular intervals.

Wear tight-fitting work clothing for all work on the valve.

Ensure that nobody can get hurt on the parts of the valve.

Immediately report any faults or noticeable changes on the valve to the
person responsible.

Never touch the pipes and the valve when these components are hot! Avoid
opening the valve unless the process plants have been emptied and
depressurised.

Observe the accident prevention regulations and all local regulations.

Safety

Subsequent changes

430BAL008372EN_4

 

11.03.2022

11

Summary of Contents for VARIVENT K





































































Reviews: