GEA Omni Page 179 Instruction Manual Download | Manualshive

Page: 179 / 238

background image

Value

Description

Cycle Off Timer

This value displays the remaining time before the compressor will stop automati-
cally. It will only be visible if Automatic Start/Stop is enabled in the configuration.
The value is measured in seconds.

Motor Start to Start Timer

This value displays the remaining time that must elapse after the compressor is
started before it may be safely started again. The value is measured in seconds.

Motor Stop To Start Timer

This value displays the remaining time that must elapse after the compressor is
stopped before it may be safely started again. The value is measured in seconds.

Oil Drain Timer

This value displays the remaining time that the compressor must wait for oil to
drain from the system before the compressor may be safely started. The value is
measured in seconds.

Accumulated Run Time
Hours

This value displays the total amount of time the compressor has run. The value is
measured in hours.

Capacity Percentage

This value displays the current reading of the capacity slide. The value is meas-
ured in percent.

kWh Demand

This value displays the currently estimated kWh demand of the compressor. The
value is measured in kWh.

3.7.3

Digital Inputs/ Outputs

Hint!

The assignment of the data points is dependent on the configuration. Check the electrical con-
nection diagram to identify the exact layout of the data points.

Value

Description

Emergency Stop

This input monitors the status of the Emergency Stop switch. It will be energized
for normal panel operation. If this input ever becomes de-energized, an Emer-
gency Stop shutdown will be triggered. The states are

On

or

Off

.

Compressor Interlock

This input monitors the status of the compressor run feedback module. It will be
energized while the compressor is running, and de-energized while the compres-
sor is stopped. If this input ever becomes de-energized while the compressor is
running, or energized while the compressor is stopped, an interlock alarm condi-
tion will be triggered. The states are

On

or

Off

.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Operating Data

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

179

«
...
177
178
179
180
181
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Abus Pages: 12

Brand: Kärcher Pages: 4

Brand: OJ Electronics Pages: 8

Brand: OJ Electronics Pages: 112

Brand: OJ Pages: 17

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: National Instruments Pages: 72

Brand: National Instruments Pages: 41

MAGNUM ALERT 3000 FIRE ALARM

Brand: NAPCO Pages: 2

Brand: Panasonic Pages: 8

Brand: DigiPower Pages: 27

nERGY bluePRINT ENGCP15001

Brand: Soundoff Signal Pages: 5

Brand: IBCcontrol Pages: 16

Brand: hotset Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands