background image

8

 D
 GB
 F
 E

96416-03.2017-DGbFEIRu

ATTENTION The oil level must be in the 

visible part of the sight glass; 
damage to the compressor 
is possible if overfilled or 
underfilled!

3

|

 Areas of application

  The compressors are filled at the factory with the following oil type:

     - für R134a, R404A/R507, R407C, R407F 

FUCHS Reniso Triton SE 55 

   - für R22 

 

FUCHS Reniso SP 46 

Compressors with ester oil charge (FUCHS Reniso Triton SE 55) are marked with an X in the type 
designation (e.g. HG

X

44e/770-4).

 3.1  Refrigerants

•  HFKW / HFC: 

 

R134a, R404A/R507, R407C, R407F

•  (H)FCKW / (H)CFC:  

R22

3.2   Oil  charge

INFO

For refilling, we recommend the above oil types.  
Alternatives: see lubricants table, Chapter 7.5

ATTENTION Compressor operation is possible within the operating limits 

shown in the diagrams. Please note the significance of the 

shaded areas. Thresholds should not be selected as design or 
continuous operation points.
- Permissible ambient temperature (-20°C) - (+60°C)
- Max. permissible discharge end temperature 140°C.

- Max. permissible switching frequency 12x /h.

- A minimum running time of 3 min. steady-state condition   
  (continuous operation) must be achieved.
For operation with supplementary cooling:
-  Use only oils with high thermal stability.
- Avoid continuous operation near the threshold.
For operation with capacity regulator:
-  Continuous operation, when the capacity regulator is activated, 

is not permissible and can cause damage to the compressor.

-  The suction gas superheat temperature may need to be reduced 

or set individually when operating near to the  threshold.

-  When the capacity regulator is activated, the gas velocity in the 

system can not under certain circumstances ensure that suffi

-

cient oil is transported back to the compressor.

For operation with frequency converter:

-  The maximum current and power consumption must not be 

exceeded. In the case of operation above the mains frequency, the 

application limit can therefore be limited.

3.3  Limits of application

max.

min.

oil level

Fig. 4

Fig. 4

HG44e 

1,6 Ltr. 
HG56e 

1,4 Ltr.

~

~

~

~

Summary of Contents for HG44e/475-4 S







































Reviews: