GEA ECOspace Operating Instruction Download Page 42 | Manualshive

Page: 42 / 66

background image

10.5.2 Removing the T.VIS A-15 Control Top

Fig.14

Prerequisite:

•

The pneumatic and electrical connections on the plant side can remain on the
control top.

Notice

The permanent magnet on the switch bar is fragile.

Damage to the permanent magnet.
► Protect the permanent magnet against impact stress.

Notice

The sensor is a sensitive component.

Damage of the sensor and failure of the valve.
► Always handle the sensor with care!

Carry out the following steps:

1.

Undo the screws (39).

2.

Remove the clamps (15).

3.

Withdraw the control top (B) via the switch bar (11) from the actuator (A.1).

4.

Unscrew the switch bar (11).

®

Done.

Hint!

Assemble the valve in reverse order. Also refer to the instruction
manual for T.VIS A-15.

Maintenance

Disassembling the Valve

430BAL010337EN_7

42

29.07.2021

«
...
40
41
42
43
44
...
»

Summary of Contents for ECOspace



































































Reviews:

No comments

Related manuals for ECOspace

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: EA Pages: 24

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: Bartec Pages: 26

Brand: V2 Pages: 48

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

ESD-5550 Series

Brand: GAC Pages: 12

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: M-Audio Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands