background image

Maintenance / servicing

36

BA.012.KYY.001.02.10.GB

9. Insert the discharge casing 0107.00.

MF-090

Fig. 39 

Discharge casing

10. Adjust the discharge casing 0107.00 via dis-

charge branch by using a spirit level.

MF-112

Fig. 40 

Discharge branch

11. Spray pump shaft 0211.00 with clean water.

Use spray bottle from Hilge assembly tool kit
(pos. 2, fig. 59).

12. Fit the stationary ring of the mechanical seal

0433.00 into the seat of the discharge casing
0107.00.
Use installation sleeve from Hilge assembly tool 
kit (pos. 12, fig. 59).

MF-115

Fig. 41 

Installation sleeve

13. Slide the assembly sleeve from Hilge assembly

tool kit (pos. 1a, fig. 59) over the pump shaft
0211.00.

MF-117

Fig. 42 

Assembly sleeve

14. Slide the rotary ring of the mechanical seal

0433.00 onto the pump shaft 0211.00.
Use installation sleeve from Hilge assembly tool
kit (pos. 12, fig. 59).

MF-121

Fig. 43 

Mechanical seal

15. Remove the assembly sleeve.
16. Assemble impeller 0230.01 .

MF-001

Fig. 44 

Impeller

17. Assemble the insert ring 0513.01.

MF-003

Fig. 45 

Insert ring

18. Insert the O-ring 0412.11.

MF-126

Fig. 46 

O-ring

Summary of Contents for DURIETTA 0













































Reviews: