background image

2 C

  

CUTOUT FOR INSTALLATION OVER A 
WARMING DRAWER

NOTE: 

Install the oven only with specific models listed on the label located on top of the oven.

NOTE: 

Additional clearances between cutouts may be required. Check to be sure the oven 

supports above the Warming Drawer location do not obstruct the required interior depth and height.

When installing a Warming Drawer below a single, double, or combination oven, a separate 
120V, 60 HZ, properly grounded receptacle must be installed. Refer to installation instructions 
packed with the Warming Drawer for specific installation requirements.

Anti-Tip Block Against 

Rear Wall Per Warming 

Drawer Requirement

2" (5.1 cm) 

Min. 

Per Warming 

Drawer 

Requirement

Continue to Section 3 for Double Wall Oven with Pedestal. Otherwise, continue to Section 4.

3 A

  

DETERMINING WHEN TO USE THE PEDESTAL 
(30” DOUBLE OVENS ONLY)

WHEN TO USE THE PEDESTAL

When replacing an older GE Appliances 30” double wall oven with a new GE Appliances model. 
Cutout height = 51-13/16” to 51-15/16”. This is our traditional cutout height.

WHEN NOT TO USE THE PEDESTAL

When replacing a 30” double wall oven from another manufacturer (ie. Whirlpool) with a new 
GE Appliances 30” double wall oven. Cutout height = 50-1/4”. You will need to verify that the 
existing cutout matches the 50-1/4” dimension.

If the new GE Appliances 30” double wall oven is being installed into new construction (ie. not a 
replacement), then the recommended installation is to use the Pedestal.

3 B

  

PEDESTAL RAIL INSTALLATION 
(30” DOUBLE OVENS ONLY)

A. 

 Position the pedestal rails with the top cutout toward the front of the opening and the flanges 
on the bottom, pointing toward the center.  Locate each rail on the floor or cabinet runner, 
slightly inward from the side of the cabinet.  Make sure the front of each rail is not protruding 
beyond the front of the cabinet opening.

B.

  Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware.

31-2000923 Rev. 1   11-21   GEA

Flanges toward 
center of cutout

Top cutout 
toward front

Attachment 
screws

Summary of Contents for ZTDX1DSSN

















Reviews: