Home
/
GE
/
Vivid S70
/
User Manual

GE Vivid S70, User Manual

Share

Page: 284 / 709

background image

Measurements and Analysis

8-6

Vivid S70 / S60

–

User Manual

BC092760-1EN

01

Assign and Measure modality

Figure 8-2. Example of a measurement study

1. Press

Measure

on the control panel.

The

Measurement

menu is displayed, showing the

measurement category for the current application
(Figure 8-2).

To change Measurement category:

1. Select the heading in the

Measurement

menu and choose

another category.

NOTE:

This can also be done from the Touch panel.

To perform measurements from a study:

1. Select the study (folder) in the

Measurement

menu.

NOTE:

This can also be done from the Touch panel.

1. Measurement category for the

current application

2.  Study
3.  Opened study
4.  Performed measurement
5.  Pre-selected measurement

6.  Access to other studies for the current measurement category.
7.  Controls for the current measurement
8.  General controls for the measurement application

«
...
282
283
284
285
286
...
»

Summary of Contents for Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vivid S70

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: Panasonic Pages: 180

Brand: BACtrack Pages: 16

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Brand: Ibiza Pages: 21

Brand: IBC Pages: 8

Brand: Ibanez Pages: 8

Brand: IAI Pages: 5

Brand: Idmed Pages: 2

Brand: Raytec Pages: 60

Brand: MAGSTIM Pages: 86

Brand: Walimex Pro Pages: 44

Brand: Otto Bock Pages: 72

Brand: Kanlux Pages: 4

Brand: CombiSteel Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands