GE TMO2D User Manual Download | Manualshive

Page: 59 / 102

background image

TMO2D Digital Display User’s Manual

51

Chapter 4. Basic Programming

4.8.5h Reset Drift?

Selecting the “Reset Drift?” option prompts the display to reset the Auto Cal drift curve to the original calibration data.

4.8.5i

View Drift Curve?

Selecting this option enables the user to view the Auto Cal drift curve.

Note:

If the unit is uncalibrated and/or has not undergone the Auto Cal procedure (no calibration data has been
previously entered), the drift values will all be 0.00 mA.

4.8.5j

Done?

AUTO CALIBRATION MENU

Reset Drift?

Press [YES] to enter the “Reset Drift?” option.

Reset Drift?
[YES] no

Use the [NO] or arrow keys to select the desired entry. Select and press [YES] to
reset the Auto Cal drift curve.

Working . . .

AUTO CALIBRATION MENU

Reset Drift?

After resetting the curve (or if you press [NO] to cancel the process), the display
returns to the Auto Cal Menu. Press [NO] to proceed to the next option.

AUTO CALIBRATION MENU

View Drift Curve?

Press [YES] to enter the View Drift Curve option.

Drift Values:
X.XX % Gas, X.XX mA

Press [YES] to scroll through the values of the drift curve.

AUTO CALIBRATION MENU
View Drift Curve?

After it goes through the points, the display returns to the View Drift Curve option.
Press [NO] to exit the option.

AUTO CALIBRATION MENU
Done?

Press [YES] to return to the Calibration Menu.

CALIBRATION MENU
Auto Cal Parameters?

Then press [NO] to exit the Auto Cal Parameters submenu.

CALIBRATION MENU
Done?

Press [YES] to exit the Calibration Menu and return to the Main Menu.

MAIN MENU
Calibration?

Press [NO] to proceed to the System Log menu.

«
...
57
58
59
60
61
...
»

Summary of Contents for TMO2D







































































































Reviews:

No comments

Related manuals for TMO2D

Brand: Baby Control Digital Pages: 16

Brand: Samsung Pages: 37

Brand: Olsberg Pages: 21

Brand: Chauvet Professional Pages: 41

Brand: Daewoo Pages: 8

MULTISYNC LCD195WVXM

Brand: NEC Pages: 64

Brand: Alienware Pages: 68

Brand: König Pages: 95

Brand: Westinghouse Pages: 15

Brand: Qardio Pages: 32

Brand: Microtek Pages: 23

Brand: Sansui Pages: 40

Brand: Hyvision Pages: 15

Brand: Proteus Pages: 11

Brand: Viotek Pages: 20

Brand: Planar Pages: 22

Brand: Abilia Pages: 24

Brand: Chassis Plans Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands