background image

Installation Instructions

A5

CAUTION:

 To avoid the risk of personal 

injury (back injury or other injuries due to excessive 

weight of the microwave) or property damage, you 

will need two people to install this microwave.
IMPORTANT: 

Do not grip or use handle during 

installation.

WARNING:

 

Risk of Electric Shock. Can 

cause injury or death: If installing unit with metal 

countertops, cover the edge of the power supply 

cord hole with the power supply cord bushing.
IMPORTANT:

 If filler blocks are not used, case damage 

may occur from overtightening screws.

MOUNT THE MICROWAVE OVEN

NOTE:

 When mounting the microwave, thread power 

cord through hole in bottom of top cabinet. Keep it 

tight throughout Steps 1–3. Do not pinch cord or lift 

microwave oven by pulling cord.

Lift microwave, tilt it forward, and hook slots at 

back bottom edge onto four lower tabs of mounting 

plate.

Rotate front of microwave oven up against cabinet 

bottom. 

1

2

Power Cord

  INSTALLING THE CHARCOAL FILTER

A4

Open the door.
Push the “Push” area on charcoal filter cover at center  

of the grille. 

Insert the top of the filter up and into the grooves on 

both sides of the inside of the top opening.  Once you 

have cleared the bottom tab, push the bottom of the 

filter in until it restes in place behind the tab.

Close the charcoal filter cover.
Close the door.

2

1

3

4
5

15

Filter

Bottom Tab

Summary of Contents for Profile PVM2188SJC



























Reviews: