background image

10

49-3000295  Rev. 0

Getting started

USING THE W

A

SHER

Cycle Options
Deep Fill

Select the 

Deep Fill

 feature for loads where extra water is desired. 

The 

Deep Fill

 feature is recommended for special case 

loads only, not for typical use.

Press and release the 

Deep Fill

 button once before starting the cycle to add 3 addition gallons of water to the wash load. 

Holding the 

Deep Fill

 button for 3 seconds will provide the deepest fill level possible; this will increase cycle time due to the 

additional time it takes to fill the washer. 
To cancel the option if desired, press the 

Deep Fill

 button again.

NOTE:

 The 

Deep Fill

 button can also be pressed after the washer has completed filling and is in the wash phase if 

additional water is desired. To stop the extra fill, press the 

Deep Fill

 button again and the water will stop.

Power Pre-wash

 

(on some models) 

Ideal for heavily soiled loads, this cycle option works with SmartDispense™ to add a brief wash, soak and drain cycle to 
loosen and remove heavy soil before starting the cycle selected.

Tangle Control™

 

(on some models) 

Setting this option will adjust your wash cycle to aid in the prevention of tangling. Your cycle time may increase when this 
option is selected. 

NOTE:

 This option is not allowed for some cycles.

Auto Soak

This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the cycle 
automatically. Repeated pressing of the 

Soak

 button will scroll through 15 minute, 30 minute, 1 hour and 2 hour selections 

and then return back to 0 soak minutes.

Deep Rinse

Set this option to provide a deep rinse

 

or when using fabric softener. It may change other settings (e.g. 

Spin

 may go to a 

higher setting) to maximize performance. Option available on all wash cycles.

Delay Wash

When the 

Delay Wash

 button is repeatedly pressed, the delay time is set from 1 (01H) to 9 (09H) hours and back to clear 

(00H) hours. If you press and hold the 

Delay Wash

 button for 3 seconds, it will immediately reset.

Extra Rinse

When you use extra detergent or bleach to clean heavily soiled clothes, use the 

Extra Rinse

 option to better remove 

additional residues. 

NOTE: 

This option is not allowed for some cycles.

Smart Wash

 

(on some models)

When enabled, the 

Smart Wash

 option will automatically sense the soil level of the load and adjust the wash cycle 

accordingly (adding or removing agitation and soaking times) to achieve excellent wash performance while minimizing wear.

Smart Rinse

 

(on some models)

The 

Smart Rinse

 feature senses the amount of soil and detergent in the current laundry cycle and determines whether 

additional water is needed to ensure a thorough rinse keeping fabrics performing like new for longer.

My Cycle Settings

 

(on some models)

As the cycle selector knob is turned, the 

Temp

Soil

 and 

Spin

 settings change to automatic pre-set default settings for each 

cycle. If you desire different default settings, select the desired options or changes to the cycle settings, then press and hold 
the 

My Cycle

 button for 3 seconds to store them. The 

My Cycle

 button will light when active. In the future, when you 

turn the selector knob to that cycle, your settings will be automatically recalled. To restore the factory defaults temporarily 
(i.e. for this load), press the 

My Cycle

 button for 1/2 second. The 

My Cycle

 light will turn off and the factory defaults will 

load. However, the next time you select this cycle, your 

My Cycle

 settings will load. If you wish to permanently restore the 

factory default settings for the cycle; when the 

My Cycle

 is active (button light on) press and hold the 

My Cycle

 button for 3 

seconds. The factory defaults will load for the selected cycle and the 

My Cycle

 light will turn off. The default settings will load 

when this cycle is selected in the future and the 

My Cycle

 light will remain off. 

NOTE:

 My Cycle saves the following options: 

Temp

Soil

Spin

Extra Rinse

Deep Fill

Auto Soak

Deep Rinse

Tangle Control

Auto

Power Clean

 and 

Gentle Care

.

Sound

 (on some models)

Use the 

Volume 

button to change the volume of the end of cycle signal and other system tones. Press the button until you reach 

the desired volume (high, medium, low) or off. On some models, this feature may only be available through the GE Appliances 
SmartHQ App.

Control Lock

Use the control lock before or during a cycle to prevent any selections from being made.

To lock/unlock the washer controls,

 press and hold the 

Rinse

 and 

Spin

 buttons for 3 seconds. The control lock icon will 

light up when it is on. 

NOTE:

 The 

Power

 button can still be used when the machine is locked.

F

Summary of Contents for Profile PTW600BSRWS




























Reviews: