manualshive.com logo in svg

GE Monogram ZV800, Installation Instructions Manual, Page: 11 / 24

Share
Download
GE Monogram ZV800 Installation Instructions Manual Download Page 11

11

Installation Instructions

PREPARE THE HOOD

•

Remove the hood from the box. Remove packaging
and tape.

•

Remove one screw on each side of the cover on the
electrical panel. Lift off the cover and set aside with
screws.

•

Stand the electrical panel upright.

•

Align the screw holes in the bottom of the panel with
the holes on the base of the hood at the front side.

•

Install 3 screws provided.

•

Snap the damper into the
exhaust outlet on the top
of the hood.

4

Remove 2 side

cover screws

Secure

electrical panel

with 3 screws

Install

damper

MOUNT THE HOOD

•

Lift the hood onto the mounting bracket.

•

Check to be sure it is level.

•

Install wood screws through the hood and into the
wall on each side of the mounting bracket. 

•

Extend the canopy forward for better access to the
rear mounting screw holes.

•

Install 2 wood screws or fasteners through the 
bottom of the hood into the wall.

5

Install a wood screw

on each side of the

mounting frame

Install bottom

mounting

screws

WALL-MOUNTED INSTALLATION—VENTED TO THE OUTSIDE

Electrical

panel

Junction box

Mounting

bracket

Inside screw

Summary of Contents for Monogram ZV800

























Reviews:

No comments