manualshive.com logo in svg

GE Monogram ZEW145, Installation Instructions Manual, Page: 18 / 20

Share
Download
GE Monogram ZEW145 Installation Instructions Manual Download Page 18

18

Installation

Component Cooktop System

Connect
Electrical

(Continued)

Step

6

White

Black

Red

White or 

Gray

Black

Branch Circuit                   Cooktop

3-Conductor Branch Circuit

Bare or

Green

+120V AC

-120V AC

Neutral

Red

White

Black

Bare or

Green

Branch Circuit                   Cooktop

4-Conductor Branch Circuit

Red

White or

Gray

Black

Bare or

Green

+120V AC

-120V AC

Neutral

DND

3-Conductor branch circuit:

• Connect red lead to branch circuit red lead.
• Connect black lead to branch circuit black

lead.

• Connect bare or green conductor and white

lead * of the cooktop to branch circuit
neutral lead, which is white or gray.

4-Conductor branch circuit:

• Connect red lead to branch circuit red lead.
• Connect black lead to branch circuit black

lead.

• Break connection between cooktop white

lead to bare or green conductor.

• Connect cooktop white lead* to branch

circuit neutral lead, which is white or gray.

• Ground unit by connecting bare conductor

of cooktop to branch circuit bare or green
lead (ground lead).

The frames of these appliances are grounded
to neutral.

* Updraft grill has no white neutral wire.
Connect only black, red and bare wires as
shown.

Electrical
Power
Requirements

Model

Voltage

Frequency

AMPS KW

ZGW124

120

60 Hz

1.0

––

ZGW125

120

60 Hz

1.0

––

ZEW145

208

60 Hz

11.0

2.3

ZEW145

240

60 Hz

12.7

3.0

ZEW155

240

60 Hz

7.3

1.8

ZEW166

240

60 Hz

13.5

3.3

ZEW176

120

60 Hz

1.8

––

Summary of Contents for Monogram ZEW145





















Reviews:

No comments