GE IC754CSF15CTD Hardware User'S Manual Download

Page: 35 / 102

GFK-2402D

Chapter 2 Overview

2-23

To install a certificate on an FTP Client

1. Double click the certificate. Select the

General

tab.

The Certificate properties are displayed.

2. Click the

Install Certificate

button.

The Certificate Import Wizard appears.

3. Click

Next

to continue.

The Certificate Store screen appears.

4. Specify whether Windows should place the certificate in a certificate

store or select another location. Click

Next

to continue.

The Completing the Certificate Import Wizard screen appears.

5. Click

Finish

to complete the installation of the certificate.

The Security Warning message appears. This message informs you
Windows will automatically trust any certificate issued by this
Certification Authority.

6. Click

Yes

to allow Windows to trust any certificate issued by this

Certification Authority.

Summary of Contents for IC754CSF15CTD







































































































Search results

Summary of Contents for IC754CSF15CTD

Reviews:

Related manuals for IC754CSF15CTD

Brands by name

Popular brands

GE IC754CSF15CTD, Hardware User'S Manual

Search results

Summary of Contents for IC754CSF15CTD

Reviews:

Related manuals for IC754CSF15CTD

Brands by name

Popular brands