background image

 

 

 

Page 9 

Hydran* M2-X Installation Guide 

 

MA-028 

Rev. 2.1,  

11-Jun-20

 

 

Software is warranted for ninety (90) days from delivery. GE represents and warrants 

that  any  software  and  firmware  covered  by  this  manual  is  free  from  functional 
deficiencies. If any functional deficiencies are discovered and are reported to GE within 
the Warranty Period, GE agrees to use due diligence to correct such deficiencies within 
30  days  after  receipt  of  such  notification.  Upon  receiving  such  notice,  GE  may  lend 
telephone support or patches. If the reported deficiencies cannot be eliminated within 
30 days, the Buyer may request, and GE shall then furnish, monthly status reports to the 
Buyer regarding the progress of GE

’s efforts to correct such functional deficiencies.

 

If Products covered by this manual do not meet the above warranties during the 

applicable Warranty Period, the Buyer shall promptly notify GE in writing but not later 
than  30  days  and  make  the  Products  available  promptly  for  correction.  GE  shall 
thereupon  correct  any  defect  by,  at  its  option,  repairing  the  defective  Products  or 
making available necessary replacement parts. 

Any failure which is the basis for a warranty claim shall not be cause for extension of 

the duration of the applicable Warranty Period. GE shall not be responsible for removal 

or replacement of systems, structures or other parts of the Buyer’s facility. If a defect in 

Products or part thereof cannot be corrected by GE

’s reasonable efforts, the parties 

shall negotiate an equitable adjustment in price with respect to such Products or part 
thereof.  All  decontamination  work  necessary  for  the  correction  of  defects  shall  be 

performed  by  the  Buyer  at  the  Buyer’s  expense.  T

he  condition  of  any  tests  shall  be 

mutually agreed upon and GE shall be notified of and may be represented at all tests 
that may be made. 

GE does not warrant Products or any repaired or replacement parts against normal 

wear  and  tear,  including  that  due  to  environment  or  operation,  including  excessive 
operation  at  peak  capability,  frequent  starting,  type  of  fuel,  detrimental  air  inlet 
conditions, or erosion, corrosion or material deposits from fluids, or which have been 
involved  in  an  accident.  The  warranties  and  remedies  set  forth  herein  are  further 
conditioned upon: 

 

Proper  storage,  installation,  operation  and  maintenance  of  the  Buyer’s 

equipment and conformance with the instruction manuals (including revisions thereto) 
provided by GE and/or its subcontractors, as applicable  

  Repair or modification pursuant to GE

’s instructions or approval 

 

The  Buyer  shall  keep  proper  records  of  operation  and  maintenance  during  the 

applicable Warranty Period. These records shall be kept in the form of log sheets and 
copies shall be submitted to GE upon its request in connection with a warranty claim by 
the Buyer. GE does not warrant any products or services of others designated by the 
Buyer where such products or services are not normally supplied by GE. 

The preceding paragraphs set forth the exclusive remedies for all claims based on 

failure of or defect in Products covered by this manual, whether the failure or defect 
arises before or during the applicable Warranty Period and whether a claim, however 
instituted, is based on contract, indemnity, warranty, tort (including negligence) or civil 

Summary of Contents for Hydran M2-X

























































Reviews: