background image

29

TERMS AND CONDITIONS:

This warranty applies only for single family domestic use in
Canada when the Refrigerator has been properly installed
according to the instructions supplied by Camco and is
connected to an adequate and proper utility service.
Damage due to abuse, accident, commercial use, and alteration
or defacing of the serial plate cancels all obligations of this
warranty.
Service during this warranty period must be performed by an
Authorized Camco Service Agent.

Neither Camco nor the Dealer is liable for any claims or
damages resulting from failure of the Refrigerator or from
service delays beyond their reasonable control.

To obtain warranty service, purchaser must present the original
Bill of Sale. Components repaired or replaced are warranted
through the remainder of the original warranty period only.

This warranty is extended to the original purchaser and any
succeeding owner for products purchased for home use within
Canada. In home warranty service will be provided in areas
where it is available and deemed reasonable by Camco to
provide.

This warranty is in addition to any statutory warranty.

WHAT IS NOT COVERED:

• Owner is responsible to pay for service calls related to

product installation and/or teaching how to use the product.

• Damage to finish must be reported within 48 hours following

the delivery of the appliance.

• Damage to finish after delivery.
• Improper installation—proper installation includes adequate

air circulation to the refrigeration system, adequate electrical,
plumbing and other connecting facilities.

• Replacement of house fuses or resetting of circuit breakers.
• Replacement of light bulbs.
• Damage to product caused by accident, fire, floods or acts 

of God.

• Loss of food due to spoilage.
• Proper use and care of product as listed in the owner’s

manual, proper setting of controls.

• Product not accessible to provide required service.
• WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL

DAMAGES.

IMPORTANT

Keep this warranty and your bill of sale as proof of original purchase and purchase date. 
Please have serial number and model number available when calling for service.

Camco Service is available coast to coast. If further help is 
needed concerning this warranty, contact:

Manager, Consumer Relations
Camco Inc., Consumer Service
1 Factory Lane, Suite 310
Moncton, New Brunswick E1C 9M3
1.800.361.3400

Staple your receipt here. 

Proof of the original purchase

date is needed to obtain service

under the warranty.

What is covered

How Long Warranted

Parts

Labour

(From Date of Sale)

Repair or Replace

at Camco’s Option

Compressor

GE Profile: Ten (10) Years

GE Profile: Ten (10) Years

GE Profile: Five (5) Years

GE and All Other 

GE and All Other 

GE and All Other

Brands: One (1) Year

Brands: One (1) Year

Brands: One (1) Year

Sealed System (including

GE Profile: Five (5) Years

GE Profile: Five (5) Years

GE Profile: Five (5) Years

evaporator, condenser 

GE and All Other 

GE and All Other

GE and All Other

tubing and refrigerant)

Brands: One (1) Year

Brands: One (1) Year

Brands: One (1) Year

All Other Parts

One (1) Year

One (1) Year

One (1) Year

CUSTOMER WARRANTY

(for customers in Canada)

Your refrigerator is warranted to be free of defects in material and workmanship.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this Limited
Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a particular purpose,
are limited to one year or the shortest period allowed by law.

Summary of Contents for GTL22JBPBS

































Reviews: