GE GTL22JBPBS Owner'S Manual & Installation Instructions Download

Page: 16 / 32

FLUSH OUT THE TUBING

Turn the main water supply on and flush out the
tubing until the water is clear.

Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.

CONNECT THE TUBING TO THE
VALVE

Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.

Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end
of the tubing into the shutoff valve and tighten
compression nut until it is hand tight, then tighten
one additional turn with a wrench. Overtightening
may cause leaks.

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.

INSTALLING THE WATER LINE

(CONT.)

Installation Instructions

Saddle-Type
Shutoff Valve

Compression
Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with
the pipe clamp.

NOTE:

Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.

Vertical Cold
Water Pipe

Saddle-Type
Shutoff Valve

Pipe Clamp

TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer
begins to swell.

NOTE:

Do not overtighten or you may crush the

tubing.

Washer

Inlet End

Pipe Clamp

Clamp Screw

ROUTE THE TUBING

Route the tubing between the cold water line and
the refrigerator.

Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.

NOTE:

Be sure there is sufficient extra tubing

(about 8 feet [244 cm] coiled into 3 turns of about
10

″

[25 cm] diameter) to allow the refrigerator to

move out from the wall after installation

Summary of Contents for GTL22JBPBS

































Search results

Summary of Contents for GTL22JBPBS

Reviews:

Related manuals for GTL22JBPBS

Brands by name

Popular brands

GE GTL22JBPBS, Owner'S Manual & Installation Instructions

Search results

Summary of Contents for GTL22JBPBS

Reviews:

Related manuals for GTL22JBPBS

Brands by name

Popular brands