7
Settings
Individual settings for cycle minutes (
Time
), dryness level (
Level
) and temperature (
Temp
) can be set from the minimum
(lowest in column) to maximum (highest in column). In general, the higher up the column, the more energy will be used.
NOTE:
The selected cycle set
Time
can be further adjusted, in one minute increments, by pressing the
Time
(plus)
and
-
(minus) buttons.
Dryness Level
-
Selection only used for
Sensor cycles. Timed cycles run for the selected time.
More
Dry
Use for heavy-duty or mixed type fabrics.
Dry
Use for a normal dryness level suitable for most loads. This is the preferred cycle for energy savings.
Less Dry
Use for lighter fabrics.
Damp
For leaving items partially damp.
Temperature
High
For regular to heavy cottons.
NOTE: Steam Dewrinkle
and
Steam Refresh
require the High temperature setting.
Medium
For synthetics, blends, delicates and items labeled permanent press.
Low
For delicates, synthetics and items labeled
tumble dry
low.
No
Heat
For fluffing items without heat. For use only with the
Air Fluff
cycle.
Extended Tumble
Use this option to minimize the wrinkles in clothes. It provides 1 hour of no-heat tumbling after the clothes are dry. If you are
using the cycle
Signal Adjust
and you select the
Extended Tumble
option, a signal will sound at the end of the drying time and
several times during the
Extended Tumble
cycle. This will remind you that it is time to remove the clothes.
Damp Alert
This option causes the dryer to beep when clothes have dried to a damp level. Remove items that you wish to hang dry. The
Damp Alert
will only beep when this option is selected (but the dry cycle will keep running). Removing clothes and hanging them
when they are damp, can reduce the need to iron some items. The light beside the button will be lit when
Damp Alert
is on.
Drum Light
The drum light will turn on if the
Damp Alert
button is pressed for 3 seconds or the door is opened. It will turn off when
the door is shut, the
Damp Alert
button is pressed again for 3 seconds or after 5 minutes if the door is left open.
Delay Dry
Press the
Delay Dry
button to set the delay start time in 1 hour increments up to 24 hours, and then back to clear (0 hours).
After selecting the delay start time, press
Start
and the delay time will count down the time remaining until the cycle starts.
NOTE:
To set the amout of delay time faster, you can press and hold the
Delay Dry
button.
Signal Adjust
Use the
Signal Adjust
button to change the volume of the button presses and the end of cycle signal. Press the button until you
reach the desired volume or off. The clothes should be removed when the end of cycle signal goes off so wrinkles do not set in.
NOTE:
Remove garments promptly at the sound of signal. Place clothes on hangers so wrinkles will not set in.
Use the
Signal Adjust
especially when drying fabrics like polyester, knits and permanent press. These fabrics should be
removed so wrinkles will not set in.
My Cycle
As the cycle selector knob is turned, the
Time
(timed dry),
Level
(dryness level) and
Temp
(temperature)
settings change
to automatic pre-set default settings. If you desire a different setting, press the appropriate button(s). Then press and hold the
My Cycle
button for 3 seconds and the dryer will “remember” these settings for that Knob Selection. In the future, when you turn
the selector knob to that cycle, your settings will be automatically recalled.
NOTE:
Signal volume cannot be set for
My Cycle
.
H
I
G
GEAppliances.com
Summary of Contents for GTD65GBPLDG
Page 9: ...9 Notes GEAppliances com...
Page 25: ...9 Notas GEAppliances com...
