Installation Instructions
/HWWKHGLVKZDVKHUUXQWKURXJKDFRPSOHWH¿OO³FLUFXODWH³SXPSRXW
cycle. This will take approximately 5 minutes.
• Check for leaks.
• If a leak is found, unplug the dishwasher, correct as necessary and
then plug the dishwasher back in.
• Open the dishwasher door and make sure most of the water has
drained. If the dishwasher did not drain, check the drain hose to be
sure it is not kinked.
/HWWKHGLVKZDVKHUUXQWKURXJKDQRWKHU¿OODQGGUDLQF\FOH&KHFN
again to be sure there are no leaks.
$WWKHHQGRIWKHVHFRQGGUDLQVHWWKHFRQWUROWRWKH2ȺSRVLWLRQ
Timer Dial Models:
²8QODWFKWKHGRRUDQGURWDWHWKHWLPHUGLDOWRWKH2ȺSRVLWLRQ
Electronic Models:
– An electronic dishwasher run in the Rinse Only cycle should shut
LWVHOIRȺDIWHUDERXWPLQXWHVRIUXQWLPH1RIXUWKHUDFWLRQLV
QHFHVVDU\LIWKHGLVKZDVKHUKDVWXUQHGLWVHOIRȺ,IWKHWHVWZDVUXQ
in a cycle other than Rinse Only, push the start pad one time and
WKHGLVKZDVKHUZLOOUHVHWDQGVKXWLWVHOIRȺLQDERXWVHFRQGV
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
STEP 1 REMOVE POWER FROM
DISHWASHER
• Unplug the dishwasher.
• Feed power cord back into its storage location.
STEP 2 REMOVE UNICOUPLE FROM FAUCET
7XUQRȺKRWZDWHU
• Relieve water pressure from the unicouple assembly before
disconnecting it from the faucet by depressing the red
pressure relief button on the unicouple.
• Depress the locking collar and remove the unicouple from
the faucet.
• Drain excess water from the unicouple by holding it below
sink level and allowing excess water to run from the hoses
into a pan or similar container to catch the water.
• Feed the unicouple and hoses back into their storage pocket.
STEP 3 STORE DISHWASHER
• Latch the dishwasher door closed.
• Roll the dishwasher into its storage location.
Depress collar to
release unicouple
from faucet
Depress red button to
release water pressure
• If the sink is 34" or higher from the floor, the excess water
in unicouple hoses cannot be drained directly into the sink.
It will be necessary to drain excess water from hoses into
a bowl or suitable container that is held outside and lower
than the sink.
HOW TO DISCONNECT THE
DISHWASHER
STEP 6 DISHWASHER WET TEST
• Plug power cord into outlet.
• Close and latch dishwasher door.
• Start dishwasher:
Timer Dial Models
– Press the Normal pad.
– Turn the dial just enough to start the dishwasher. The dial should
point to “Hot Start”. Do not turn the dial too far. If you turn it too
IDU\RXZLOO´E\SDVVµWKH¿OO
Electronic Models
– Press “Rinse Only.”
– Press the start pad one time.
• Check to be sure that water enters the dishwasher. This could take
up to 4 minutes on dial models.
• If water does not enter the dishwasher:
– Check to be sure that the water is turned on.
²/LJKWO\WDSWKHÀRRGÀRDWFRYHUWRGLVORGJHDVWXFNÀRRGÀRDW
²2QGLDOPRGHOVPDNHVXUH\RXGLGQRWWXUQWKHGLDOSDVWWKH¿UVW
¿OO,IWKLVKDSSHQHGXQODWFKWKHGRRUDQGURWDWHWKHGLDOWR´2Ⱥµ
Relatch the door and turn the dial one click at a time until the
dishwasher starts.
– On electronic models, make sure the start pad was pressed one
time only.
Flood Float
Cover
Appliance Park
Louisville, KY 40225
