GE GCG200NGWC Service Manual Download Page 42

Page: 42 / 58

7. Cold of Vegetable Case

8. Operation Noise of Refrigerator

8-1. Compressor operation noise

- Compressor sound is somewhat normal because it works like a heart to circulate the refrigerant in the pipes.

- Rattling or metalic touch sound of motor, piston of compressor can be heard when it starts or stops.

TROUBLE SHOOTING

Remark

Temperature setting

is 'MAX'?

Start

Check Valve

operation is ok?

Any Refrigerator

sensor Error?

Change to 'MIDDLE' mdoe

Yes

Repair or change the new

Sensor is ok?

Check sensor connection

(Check the connector to Main PCB)

Yes

Refrigerator Foot

level is ok?

Start

Rubber absorber to

hold compressor is

distorted or aged?

Sound from

compressor itself or

vibration?

Adjust foot leveling

(Refer to User Manual)

Yes

Change the Rubber

absorber

Yes

Attach a restrainer on the

compressor head to reduce

vibration and high frequency noise

Change the compressor

Summary of Contents for GCG200NGWC



























































Search results

Summary of Contents for GCG200NGWC

Reviews:

Related manuals for GCG200NGWC

Brands by name

Popular brands

GE GCG200NGWC, Service Manual

Search results

Summary of Contents for GCG200NGWC

Reviews:

Related manuals for GCG200NGWC

Brands by name

Popular brands