GE Dishwasher Installation Instructions Manual Download Page 14

Dishwasher Installation

–  Check the electrical connection to the water  

valve. The red electrical connector should be  
plugged into the dishwasher water valve. If it is 
not plugged in, turn off electrical power to the 
dishwasher. Plug the red connector into the dish-
washer water valve and then restore power.

 

 
 

  Check for leaks under the dishwasher. If a leak is 

found, turn off power, tighten connections and 
restore power.

  Check for leaks around the door. A leak around 

the door could be caused by the dishwasher door 
rubbing or hitting adjacent cabinets. Reposition 
the dishwasher if necessary. See Steps 11, 12  
and 13.

  Most dishwasher models will drain about 3 min-

utes after the first fill. Check the drain line for 
leaks when dishwasher drains. If leaks are found, 
turn off power, correct as necessary and then 
restore power. 

  Open the dishwasher door and make sure most  

of the water has drained. If the water does not 
drain, check to be sure disposer plug has been 
removed and/or air gap is free of debris.

  Let the dishwasher run through another fill and 

drain cycle. Check again to be sure there are no 
leaks.

  At the end of the second drain, unlatch the door 

and rotate the dial to the “OFF” position.

14

STEP 19:  DISHWASHER WET TEST  

CHECK LIST

  Turn on power supply or if power cord is used, 

plug it into the wall outlet.

  Latch dishwasher door. 

  Press the “Normal” pad, and then turn control dial 

just enough to start dishwasher. Be careful not to 
turn the dial past the first water fill. Dial should 
point to “Hot Start Option”.

  Check to be sure that water enters the dish-

washer. This could take up to 4 minutes. 

  If water does not enter the dishwasher try the 

following to correct the problem: 
– Check to be sure that the water is turned on 
– Lightly tap the flood float cover to  
  dislodge a stuck flood float. 

Flood Float
Cover

Appearance varies by model. 

Red Connector

Pots

&Pans

Cycles

Options

Hot Start

Option

Start

Off

Plate Warmer

(Heated Dry On)

Rinse Only

(Heated Dry Off)

Light Wash

Normal

Wash

Heated

Dry

Reset

Option

Summary of Contents for Dishwasher

















Reviews: