GE Dishwasher Installation Instructions Manual Download Page 1

GE Consumer & Industrial

Appliances

Installation Instructions

Spacemaker

®

 Dishwasher

If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com

IMPORTANT

 – The dishwasher MUST be 

installed to allow for future removal from the 

enclosure if service is required.

If you received a damaged dishwasher, you should 

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for 
available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS 

shown throughout these instructions. While 

performing installations described in this booklet, 

gloves and safety glasses should be worn.

READ CAREFULLY. 

KEEP THESE INSTRUCTIONS.

IMPORTANT

 

– Observe all governing codes 

and ordinances.

• 

Note to Installer

 – Be sure to leave these 

instructions for the consumer and local inspector’s 
use.

• 

Note to Consumer

 – Keep these instructions with 

your Owner’s Manual for future reference.

• 

Skill Level

 – Installation of this dishwasher requires 

basic mechanical, electrical and plumbing skills. 

Proper installation is the responsibility of 

the installer. Product failure due to improper 

installation is not covered under the GE 

Appliance Warranty. See warranty information.

• 

Completion Time – 1 to 3 Hours

. New installations 

require more time than replacement installations.

• 

Sink Requirement

 - This Spacemaker

®

 dishwasher 

is designed to be installed under a special shallow 
sink. Three types of sinks are available: GPF95, a 
single bowl sink with the drain hole on the right 
side of the sink; GPF96, a single bowl sink with the 
drain hole on the left side of the sink; and GPF97, a 
double bowl sink. Purchase these sinks from your 
authorized GE appliance dealer.

STOP

BEFORE YOU BEGIN

Read these instructions completely and
carefully.

Pots

&Pans

Cycles

Options

Hot Sta

rt

Option

Start

Off

Plate W

armer

(Heated

 Dry On

)

Rinse On

ly

(Heated

 Dry Off

)

Light W

ash

Normal

Wash

Heated

Dry

Reset

Option

Summary of Contents for Dishwasher

















Reviews: