background image

ASTAT 

®

-IBP Plus Service Instructions

2

Prices and data subject to change without notice.

Logic Board Replacement

CAUTION:

 

Always handle circuit boards by their edges

and do not distort the parts on the circuit boards.

ATTENTION: 

Il faut toujours manipuler les plaques de

circuits par leurs côtés et ne pas déformer les pièces sur

les plaques de circuits.

1.

Remove the ASTAT-IBP cover as described in steps

1–2 of 

Cover Removal and Replacement

.

2.

Unplug the two ribbon cables from the Logic Board,

as shown in Figure 3.

3.

Remove the four corner screws holding the Logic

Board to the stand-offs below the Logic Board. Lift

the Logic Board straight up to remove it, as

illustrated in Figure 4.

4.

Reassemble the Logic Board to the starter. With the

display on the Logic Board at the upper left corner,

place the board on the stand-offs. Reattach the four

screws holding the Logic Board to the stand-offs.

5.

Reattach the two ribbon cables. Ensure that the

ribbon cable at the bottom of the ASTAT-IBP is fully

seated on both circuit boards and that the ribbon

cable does not interfere with or touch the cover.

6.

Reinstall the plastic cover and the terminal

connectors as described in steps 3–4 of 

Cover Removal

and Replacement

.

Figure 3. Logic board and part locations.

Figure 4. Removing the Logic Board.

Screws

Logic Board

Power Supply

Board

Unplug Cable

Ribbon

Logic Board

Cable Ribbon

Summary of Contents for DEH-40417



















Reviews: