background image

4

LOCATION OF YOUR DRYER

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or outside weather

conditions.

2. In an area where it will come in contact with curtains, drapes,

or anything that will obstruct the flow of combustion and
ventilation air.

3. On carpet. Floor 

MUST

 be solid with a maximum slope of 1

inch (2.54 cm).

INSTALLATION IN RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom, recess or closet,

MUST

 be exhausted outdoors.

2. No other fuel burning appliance shall be installed in the

same closet as the Gas dryer.

3. Your dryer needs the space around it for proper ventilation.

DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A

SOLID DOOR.

CLOSET DOOR

1" (2.54 cm)

0" (0  cm)

4. A minimum of 120 square inches (774.2 square cm) of

opening, equally divided at the top and bottom of the door,
is required. Air openings are required to be unobstructed
when a door is installed. A louvered door with equivalent
air openings for the full length of the door is acceptable.

MINIMUM INSTALLATION CLEARANCES (Inches)

FRONT

SIDES

REAR

TOP

Alcove

0 (0 cm)

0 (0 cm) 0 (0 cm) 15 (38.1 cm)

Closet

1 (2.54 cm) 0 (0 cm) 0 (0 cm) 15 (38.1 cm)

Closet door ventilation required: 2 louvered openings each 60
square inches (387 square centimeters) — 3 inches (7.6 cm)
from bottom and top of door.

THIS DRYER MUST BE EXHAUSTED OUTDOORS.

5. The following illustrations show minimum clearance

dimensions for proper operation in a recess or closet
installation.

60 SQ. IN.

(387.1 SQ. CM)

60 SQ. IN.

(387.1 SQ. CM)

15" (38.1 cm)

0" (0 cm)

Summary of Contents for DCCH43GAWW









Reviews: