background image

Additional Information and Warnings

FCC Compliance Statement Compliance Notice: 

Warning: Changes or modifications to this unit not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause harmful 

interference to radio communications.
However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user 

is encouraged to try to correct the interference by one or more of the following 

measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that  

  to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help 
The device must not be co-located or operating in conjunction with any other 

antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any 

interference received, including interference that may cause undesired operation.

Summary of Contents for Cync CFIXCNLR4C1













Reviews: