GE Built-In Dishwashe Installation Instructions Manual Download Page 8

Page: 8 / 16

212Dia9

Power Cord

(If Used)

Insulation

Blanket

Water

Line

Maximum Drain Hose

Length 10'

House

Wiring

Drain

Hose

Figure N

STEP 9: INSTALL DRAIN HOSE,

THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain

hose into the hole in cabinet side. If a power cord is used,
guide the end through a separate hole.

STEP 8: POSITION WATER LINE

AND HOUSE WIRING

• Position water supply line and house wiring on the floor of the

opening to avoid interference with base of dishwasher and
components under dishwasher.

Figure M

661Dia32

Water

Line

House

Wiring

Tip: Prevent unnecessary service call charges for no ﬁ ll,

drain or noise concerns

Position utility lines so they do not interfere with anything
under or behind the dishwasher.

Dishwasher Installation

STEP 10: SLIDE DISHWASHER

THREE-FOURTHS OF THE WAY

INTO CABINET

IMPORTANT

–

Do not push against front panel

with knees. Damage will occur.

• Grasp the sides of the front panel and slide dishwasher into

the opening a few inches at a time.

• As you proceed, pull the drain hose through the opening

under the sink. Stop pushing when the dishwasher extends
about 6 inches forward of adjacent cabinets.

• Make sure drain hose is not kinked under or behind the

dishwasher.

• Make certain the house wiring, drain line and water line do

not interfere with components under dishwasher.

Figure O

Figure P

STEP 11: INSTALL TRIM PIECES

(some models)

Skip this step if trim is not supplied with the dishwasher.

In this step you will need the trim pieces set aside in Step 1.

• Position the trim pieces so the lips face toward the

dishwasher door.

• Select a long trim piece and press it onto the left side tub

ﬂ ange. Start with the top edge and press the trim piece
completely onto the tub ﬂ ange as you move towards the
bottom. Repeat for the right side tub ﬂ ange trim piece.

• Install remaining trim piece on the top tub ﬂ ange.

��

Summary of Contents for Built-In Dishwashe

















Search results

Summary of Contents for Built-In Dishwashe

Reviews:

Related manuals for Built-In Dishwashe

Brands by name

Popular brands

GE Built-In Dishwashe, Installation Instructions Manual

Search results

Summary of Contents for Built-In Dishwashe

Reviews:

Related manuals for Built-In Dishwashe

Brands by name

Popular brands