49-5000636 Rev. 0
5
Controls
Cool Mode
Use the COOL mode for cooling.
To set the COOL mode:
1. Press the
MODE
pad until the
COOL
indicator light is lit.
2. Press the
FAN
S,*+0(',80RU/2:
fan speed.
3. Press
+ or -
to set the desired temperature between
64°F and 86°F in 1°F increments.
After settings have been made, the display will not
change back to show the room temperature.
The temperature control is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
temperature control at a lower number and the indoor
air will become cooler. Set the temperature control at a
higher number and the indoor air will become warmer.
NOTE:
,IWKHDLUFRQGLWLRQHULVRIIDQGLVWKHQWXUQHGRQ
while set to COOL, it will take approximately 3 minutes
for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling
—Select the COOL mode and
+,*+0(',80RU/2:IDQVSHHGZLWKDPLGGOHVHW
temperature.
For Maximum Cooling
—Select the COOL mode
DQG+,*+IDQVSHHGZLWKDORZHUVHWWHPSHUDWXUH
For Quieter & Nighttime Cooling
—Select the
COOL mode and LOW fan speed with a middle set
temperature.
NOTE:
,I\RXVZLWFKIURP&22/RU'5<PRGHVHWWLQJWR
OFF, wait 3 minutes before restarting.
FAN Mode
Use the FAN mode to provide air circulation and filtering
without cooling.
To set the FAN mode:
• Press the FAN pad until the desired indicator light for
high, medium, or low fan speed is lit.
Since fan only settings do not provide cooling, a set
temperature will not be displayed. After FAN speed has
been set, the display will change back to show the room
temperature.
The exhaust hose and window kit do not need to be
installed when operating in fan mode.”
HEAT Mode
Use the Heat mode at Low, Med, High or Auto Fan
6SHHGIRUKHDWLQJ8VHWKH7HPSHUDWXUH,QFUHDVH
/ Decrease (-) pads to set the desired temperature
between 64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The heater will cycle on and off to keep the
room at the set level of comfort.
Power Outage Recovery Feature
,QWKHFDVHRIDSRZHURXWDJHRULQWHUUXSWLRQWKHXQLWZLOO
automatically re-start in the settings last used after the
power is restored.
127(,IWKH7,0(5ZDVVHWEHIRUHWKHSRZHURXWDJHLW
will need to be reset after power is restored.
USING THE
AIR CONDITIONER
Set Temperature will be shown when unit is in operation.
DRY Mode—Dehumidification
Use the DRY mode to provide dehumidification only.
The fan will run at a fixed speed at this setting, so a fan
speed cannot be set. Keep windows and doors closed
for the best dehumidifying effects.
To set the DRY mode:
•Press the
MODE
pad until the DRY indicator light is lit.
,QWKH'5<PRGHDVHWWHPSHUDWXUHZLOOQRWEH
displayed. After DRY mode has been set, the display will
change back to show the room temperature.
NOTE:
,I\RXVZLWFKIURPD'5<VHWWLQJWR2))RUWRD
fan setting, wait at least 3 minutes before switching back
to a DRY setting.
,IXVLQJWKHXQLWLQWKH'5<PRGHDVDGHKXPLGLILHUIRU
an extended time.
1 . Unplug the power cord.
2. Connect a ½” Outer diameter flexible drain hose to
the drain port and drain to floor drain.
3. Reconnect the power cord and press the MODE pad
until the DRY indicator light is lit.
