GE Advent, Installation Instructions Manual

Page: 42 / 116

40
Advent Commercial Fire System
Accessory Modules
The items below allow you to add, delete, list, and modify
SuperBus 2000 devices and settings.
Add (Learn) Bus Devices
48001
(Accessory)
(Default = n/a) Use this item number to force the panel to scan for
bus devices once they have been correctly connected to the panel.
Note
All SuperBus 2000 devices are added to partition/area 1
initially. Use item number 48004,
Bus Device Partition/
Area , to assign devices to different partitions/areas once
added.
To force the Panel to Scan for Bus Devices:
Once in program mode enter
48001
. The display will
show DEVICES ADDED , then it will list the added devices as
shown.
DEVICE nn ID xxxxxxxx PARTITION/AREA z
Where n is the 2-digit device number (01–62), xxxxxxxx is the
8-digit ID number (address), and z is the partition/area number
(0–8).
Delete/Change Bus Device ID
48002
(Accessory)
(Default = n/a) Use this item number to delete bus devices or
change device IDs. If you are deleting bus devices, you must
delete them one at a time.
Note
Deleting the device does not delete the bus text associ-
ated with the deleted device. To delete device text use
item number 49002.
To Delete/Change Bus Device ID:
1. Once in program mode enter
48002
. The display
shows ENTER DEVICE ID OR PRESS * TO CANCEL.
2. Enter the 8-digit device ID of the device you wish to
delete/change (located on module) and press
ƒ
.
3. The display shows ENTER NEW DEVICE ID OR ENTER
0 TO DELETE .
4. Enter a new device ID or enter 0 .
5. Press
ƒ
. The panel displays DEVICE ID xxxxxxxx
DELETED, or DEVICE CHANGE OK .
6. To delete/change another device ID, repeat the above pro-
cedure.
Bus Device Text
49002
(Accessory)
(Default = none) Use the following guidelines to “name” bus
devices.
‰
Use the item numbers that appear in Table B.2 on page 92
for characters and words listed there.
‰
If a desired word does not appear in Table B.2, create it
using the characters (custom text).
‰
When using words from Table B.2, spaces between them
appear automatically. When using characters from Table
B.2 to create words, you must reserve an item number for
a ‘space’ after the word.
‰
Each character or word uses up one item number. For
example, a word from the list counts as one item number.
A created word (such as BOY’S) counts as six item num-
bers—4 letters, 1 apostrophe, and 1 space.
‰
Only 8 item numbers are allowed for each bus device
name, so plan ahead before programming device text. You
may need to abbreviate words to avoid running out of item
numbers.
To program Bus Device Text:
1. Once in program mode enter
49002
. The display
shows ENTER DEVICE ID OR PRESS * TO CANCEL .
2. Enter the desired device ID (located on module) and press
ƒ
. The display shows TEXT FOR DEVICE xxxxxxxx IS
current text . ENTER TEXT NUMBERS OR PRESS # TO
ACCEPT .
3. Enter the numbers of the desired characters or words. If
you make a mistake press
‚
to start over.
4. Once all numbers have been entered, press ƒ to accept.
The display shows the new device text.
To delete Device Text:
1. Once in program mode enter
49002
. The display
shows ENTER DEVICE ID NUMBER OR PRESS * TO
CANCEL .
2. Enter the desired device ID number and press
ƒ
. The dis-
play shows TEXT FOR DEVICE xxxxxxxx IS current text .
ENTER TEXT NUMBERS OR PRESS # TO ACCEPT .
3. Enter
000
and press
ƒ
. The display shows TEXT FOR
DEVICE xxxxxxxx IS NO TEXT .
List Bus Devices
48003
(Accessory)
(Default = n/a) Use this item number to list information about
existing bus devices. The system will list the device address
number, device ID number, and the partition/area number.
To List Bus Devices:
Once in program mode enter
48003
. The display will show
DEVICE nn, ID xxxxxxxx, PARTITION/AREA n.
The panel will scroll through and display information about each
device. To skip forward press
ƒ
. To exit press
‚
. Once the panel
lists all the bus devices it will return to the program menu.