GE 32GT720YX4, Technical Service Data

Page: 3 / 16

ERROR CODES CHART
SET 4679 P SET 4679 P
SET 4679 P SET 4679 P SET 4679 Paaaaaggggge 1
e 1
e 1 e 1 e 1
Err Err Err Err Error Code or Code or Code or Code or Code
DEC DEC DEC DEC DEC HEX HEX HEX HEX HEX Err Err Err Err Error Location or Location or Location or Location or Location Condition Indicated Condition Indicated Condition Indicated Condition Indicated Condition Indicated
0 00 No error code -
1 01 16.0V fault 16.0V STBY source is failing.
3 03 12.0V run fault 12.0V source is failing.
4 04 T4 Chip Run supply failed.
8 08 T4 Chip X-ray protection caused high voltage shutdown.
9 09 T4 Chip (POR) Power supply problem at (POR) power on reset.
10 0A F2 PIP module error (POR) Power supply problem at (POR) power on reset/PIP.
11 0B Stereo decoder (POR) Power supply problem at reset/Stereo decoder.
16 10 Run IIC Bus held low Run IIC clock or data held low.
18 12 Standby IIC Bus held low Standby IIC clock or data held low.
23 17 Gemstar Board Guide fatal error on set using Gemstar Board.
24 18 Gemstar Board Task monitor error on set using Gemstar Board.
25 19 Gemstar Board Watchdog error on set using Gemstar Board.
26 1A Gemstar Board Task monitor error on set using Gemstar Board.
32 20 Gemstar Board CPU error on set using Gemstar Board.
34 22 Gemstar Board Gemstar fails to acknowledge.
44 2C F2 PIP module error F2PIP fails to acknowledge.
102 66 Octal DAC Octal DAC fails to acknowledge.
128 80 Stereo decoder Stereo decoder fails to acknowledge.
160 A0 Main or PIP tuner EEPROM Main or PIP tuner EEPROM fails to acknowledge.
186 BA T4 Chip T4 Chip fails to acknowledge.
196 C4 Main tuner PLL/DAC Main tuner PLL IC fails to acknowledge.
198 C6 Main tuner PLL/DAC Main tuner DAC IC fails to acknowledge.
ERR ERR
ERR ERR ERROR CODES
OR CODES
OR CODES OR CODES OR CODES
If certain failures occur, the matching error codes will be stored in the EEPROM. These error codes will be displayed in parameters 1, 2, and 3. The first
failure error code will be stored at parameter 1 and the second failure error code will be stored at parameter 2. Parameter 3 will be updated to display the
most recent failure occurred in the chassis. If a failure of a bus IC occurred, the normal acknowledgment checking of that bus will be disabled in the
service mode and the address of that IC which failed will be stored in one of the error code parameters. After every repair is done to the chassis it is
recommended to check the error code parameters, and reset them back to value 0.
Impor Impor Impor Impor Important P tant P tant P tant P tant Par ar ar ar arts Inf ts Inf ts Inf ts Inf ts Information ormation ormation ormation ormation
ν
The parts listed here are those not usually available from a well-stocked supply cabinet or bin.
ν
Where items may be replaced with equivalent parts, several alternates are shown from participating vendors.
ν
On the parts lists, safety items are marked with a # # # # # to remind you that only exact replacements are recommended for
these items.
ν
When ordering parts, state the model number, part number, and description.
Obtaining P Obtaining P
Obtaining P Obtaining P
Obtaining Par ar
ar ar
arts ts
ts ts
ts
Many of these parts are available from your local Sams authorized distributor or the manufacturer of the equipment. Call
Sams for the name of your nearest distributor:
800-428-7267
Or consult the Sams Annual Index for the address of the original equipment manufacturer.
PPPPPar ar
ar ar articipating
ticipating
ticipating ticipating ticipating VVVVVendor
endor
endor endor endorsssss
Information on test equipment and replacement parts is listed in these pages for the following participating vendors.
Consult the Sams
Annual Index
for their current address.
ν
NTE Electronics, Inc. (NTE)
ν
Sencore, Inc.
TEST EQ TEST EQ
TEST EQ TEST EQ
TEST EQUIPMENT UIPMENT
UIPMENT UIPMENT
UIPMENT
Test equipment listed by participating manufacturer illustrates typical or equivalent equipment used by Sams
engineers to obtain measurements. This equipment is compatible with most types used by field service technicians.
Equipment Equipment
Equipment Equipment Equipment
Sencore No. Sencore No.
Sencore No. Sencore No. Sencore No.
Oscilloscope SC3100
Generators
RGB CM2125
Multiburst Signal VG91
Color Bar VG91
TV Stereo VG91
Digital VOM SC3100
Frequency Meter SC3100
Hi-Voltage Probe HP200
Accessory Probes TP212
Equipment Equipment Equipment Equipment Equipment Sencore No. Sencore No. Sencore No. Sencore No. Sencore No.
Isolation Transformer PR570
Capacitance Analyzer LC102
CRT Analyzer CR7000
AC Leakage Tester PR570
Inductance Analyzer LC102
Flyback Yoke Tester TVA92
Field Strength Meter SL753
Transistor Tester TF46
Horizontal Analyzer HA-2500
Video Analyzer VG91, TVA92