manualshive.com logo in svg

GE Security NetworX Series NX-8V2, Installation Instructions Manual

Share
Download
GE Security NetworX Series NX-8V2 Installation Instructions Manual Download Page 10

NX-8V2-Control Panel

Installation Instructions

10

Specifications

 

Operating power 

16.5 VAC 40 or 50 VA transformer

Auxiliary power
     w/25 VA transformer
     w/40 or 50 VA transformer 

(MG Electronics part 

number 22-156 for US or 

22-156-CN for Canadian 

installations)

12 VDC regulated 500 mA
12 VDC regulated 1 A

Loop resistance
     Standard loop

300 ohms maximum

Fuse

Type T 200 mA 250 VAC

Built in siren driver 

Two tone (temporal and yelp)

Loop response

Selectable 50 mS or 500 mS

Operating temperature

32 to 120°F (0 to 49°C)

LED keypad
     Current draw
     Zones normal w/o sounder
     Dimensions

130 mA max.
55 mA
6.4 x 4.0 x 1.1 in. (16.3 x 10.2 x 2.8 cm)

NX148E LCD keypad
     Current draw
     Without sounder
     Dimensions

110 mA max.
75 mA
6.4 x 5.3 x 1.0 in. (16.3 x 13.5 x 2.5 cm)

Metal enclosure dimension

11.25 x 11.25 x 3.50 in. (28.58 x 28.58 x 8.90 

cm)

Shipping weight

9 lb. (4.1 kg)

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the 

following conditions: 
1. This device may not cause harmful interference. 
2. This device must accept any interference received, including interference that 

may cause undesired operation. 

Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 
Complies with Part 68 FCC Rules.
ACTA (FCC) ID: GCQUSA-33408-AL-E
IC: 1175A-NXV2 

Technical support

888 GE Security (888.437.3287). Toll-free in the US, Puerto Rico, and Canada. 

503.885.5700 outside the toll-free area or contact your local dealer. 

www.gesecurity.com

  

   

 

Summary of Contents for NetworX Series NX-8V2











Reviews:

No comments

Brands by name

Popular brands

Load more brands