GE Multilin 469 Instruction Manual Download | Manualshive

Page: 214 / 338

background image

5–72

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

RTDs 1 through 6 default to “Stator” RTD type. There are individual alarm and trip
configurations for each RTD. This allows one of the RTDs to be turned off if it malfunctions.
The alarm level is normally set slightly above the normal running temperature. The high
alarm is usually set as a warning of a trip or to initiate an orderly shutdown before tripping
occurs. The trip level is normally set at the insulation rating. Trip voting has been added for
extra reliability in the event of RTD malfunction. If enabled, a second RTD must also exceed
the trip temperature of the RTD being checked before a trip will be issued. If the RTD is
chosen to vote with itself, the voting feature is disabled. Each RTD name may be changed if
desired.

5.9.3

RTDs 7 to 10

PATH: SETTINGS

ZV

S8 RTD TEMPERATURE

ZV

RTD #7(10)

MESSAGE

RTD #1 TRIP

TEMPERATURE:

Range: 1 to 250°C in steps of 1

RTD

#7

[

Z

]

RTD #7 APPLICA-

TION:

Range: Stator, Bearing, Ambient, Other,

None

MESSAGE

RTD #7 NAME:

Range: 8 alphanumeric characters

MESSAGE

RTD #7 ALARM:

Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3, Alarm &
Auxiliary3, Auxiliary2, Aux2 &
Aux3, Auxiliary3

MESSAGE

RTD #7 ALARM

TEMPERATURE: 80°C

Range: 1 to 250°C in steps of 1

MESSAGE

RTD #7 HIGH

ALARM:

Range: Off, Latched, Unlatched

MESSAGE

HIGH ALARM

RELAYS:

Range: Alarm, Alarm & Auxiliary2,

Alarm & Aux2 & Aux3, Alarm &
Auxiliary3, Auxiliary2, Aux2 &
Aux3, Auxiliary3

MESSAGE

RTD #7 HIGH ALARM

TEMPERATURE: 80°C

Range: 1 to 250°C in steps of 1

MESSAGE

RTD #7 ALARM

EVENTS: Off

Range: On, Off

MESSAGE

RTD #7 TRIP:

Off

Range: Off, Latched, Unlatched

MESSAGE

RTD #7 TRIP VOT-

ING:

Range: RTD #1 to RTD #12

MESSAGE

ASSIGN TRIP

RELAYS:

Range: Trip, Trip & Auxiliary2, Trip &

Aux2 & Aux3, Trip & Auxiliary3

MESSAGE

RTD #7 TRIP

TEMPERATURE: 90°C

Range: 1 to 250°C in steps of 1

«
...
212
213
214
215
216
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Zander Aachen Pages: 4

Brand: Keithley Pages: 58

Brand: Riyue Pages: 2

Brand: ASO Pages: 20

Brand: ZIGBEE Pages: 4

Brand: Eaton Pages: 64

Brand: Siemens Pages: 7

Relion 615 series

Brand: ABB Pages: 20

Brand: ABB Pages: 24

Brand: ABB Pages: 3

Brand: ABB Pages: 24

Brand: ABB Pages: 2

Brand: ABB Pages: 4

Brand: ABB Pages: 16

Brand: ABB Pages: 16

Brand: ABB Pages: 2

Brand: ABB Pages: 28

Brand: ABB Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands