background image

 

 

 

 

3. BEFORE THE UPGRADE 

 

3.1   Backup 

 

Create  a  snapshot  of  the  OS  partition  with 

Rescue  mode 

before  you  try  to  apply  the  upgrade. 

Note  that  the 

Rescue  mode 

function  is  only  available  for 

SATA 

OS  hard  disk.  If  you  are 

unfamiliar with this procedure, please refer to the document 

GDC_system_backup_and_recovery.

 

 

3.2   Swapping IMB 

 

1. Power off the server and projector. 

2. Remove the original Media Block from projector (SX-2000). 

3. Remove the Enigma board from Projector (Barco S2 projectors). 

4. Install the New IMB into Projector. 

5. Power on the projector and server. 

 

3.3   Connections 

 

1.  Make sure the IMB is powered up inside the projector correctly. 

2.  SX-2000A/T eth0 IP must NOT be 192.168.1.X (recommend it to be 192.168.0.X). 

3.  SX-2000A/T eth0 is connected to projector Ethernet (either directly or via switch). 

4.  SX-2000A/T eth2 IP must NOT be 192.168.1.X. eth2 is available after installing the additional 

gigabit network card. 

5.  SX-2000A/T eth1 is directly connected to IMB Ethernet 2.  

IMPORTANT NOTE: 

Projector should not use 192.168.2.X IP as this IP range is reserved for 

IMB internal use. If projector IP is set to 192.168.2.X, the server will not be able to connect to 
the security manager (SM) after upgrade. 

 

 

3.4   Notes 

 

1. SX-2000(A/T)R server serial number and HFR IMB serial number should be the same, please 

request this from your service provider. 

 
2. Perform the marriage of the HFR IMB with the projector on the projector

’s interface or in the 

server’s SMS. 

 
3. After replacement of the HFR IMB, the below screen (Figure 1) will be shown after rebooting. 

This is normal.

 

Summary of Contents for SX-2000ATO




















Reviews: