background image

6

F 8S & F 8ST Natural Gas

Category of Appliance  

F 8S

II

2H3P

Category of Appliance  

F 8ST

I

2H

The appliance is set for Gas Type G20 at 20mbar.

Heat Input 

(gross) High Med Low

Low

kW

3.06

2.21 1.50

1.27

Btu/h

10,440 7,540 5,118 4,333

Heat Output 

(gross) High Med Low

Low

kW

2.26

1.48 0.6

0.80

Btu/h

7,700 5,050 2,047 2,730

Setting Pressure

Cold

F Range

mbar

19.25 ± 0.75

in wg

7.7 ± 0.3

Setting Pressure

Cold

Comfortstat

mbar

20.00 ± 1.00

in wg

8.0 ± 0.4

Injector Size

CO

1

Nox Class

2

Gas Rate

on HIGH

0.29 m

3

/h (10.28 ft

3

/h)

Gas Connection

F 8S - 

1

/

4

(

1

/

4

BSP external)

F 8ST 

- 8mm nut and olive

Ignition

Piezo Spark 

Packed Weight

F 8S & F 8ST

24.4 kg (54 lbs)

Dimensions

F 8S 

F 8ST

Height

430mm

430mm

Width

516mm

516mm

Depth

152mm

170mm

(from the wall)

Controls

Rotary gas tap allowing

Non Thermostat

manual adjustment 

between low, medium 

and high output.

Flame failure device.

Controls

Rotary thermostat allowing

Comfortstat

a lowt position and 

adjustment between low and 

high temperature settings.

Flame failure device.

Thermocouple

Output

8-13mv

Heat Exchanger

Cast Iron

2.0 Technical Data  

F 5 & F 5S Natural Gas

Category of Appliance     

II

2H3P

The appliance is set for Gas Type G20 at 20mbar.

Heat Input 

(gross) High

Med

Low

kW

2.05

1.41

0.86

Btu/h

7,000

4,800

3,000

Heat Output

(gross) High

Med

Low

kW

1.5

0.98

0.57

Btu/h

5,100

3,350

1,950

Setting Pressure

Cold

mbar

19.7 ± 0.75

in wg

7.9 ± 0.3

Injector Size

CO

2

Nox Class

3

Gas Rate

on HIGH

0.195 m

3

/h (6.89 ft

3

/h)

Gas Connection

1

/

4

(

1

/

4

BSP external)

Ignition

Piezo Spark 

Packed Weight

F 5

F 5S

18 kg

18.4 kg

(39.7 lbs)

(40.6 lbs)

Dimensions

F 5

F 5S

Height

394mm

394mm

Width

426mm

450mm

Depth

126mm

128mm

(from the wall)

Controls

Rotary gas tap allowing

manual adjustment 

between low, medium 

and high output.

Flame failure device.

Thermocouple

Output

8-13mv

Heat Exchanger

Cast Iron

Except

Comfort

Stat 

Comfort

Stat 

Except

Comfort

Stat 

Comfort

Stat 

Installer Guide

Except

Comfort

Stat 

Except

Comfort

Stat 

© GDC Group Ltd. 2012

Summary of Contents for Comfortstat 2 F 8ST





























Reviews: