GBC StreamWire
7/23/2020
Repairs/Adjustments
4-199
ADJ 1.16 Element Feeder Angle Adjustment
For proper operation, the element holder module should mate to the
element feeder without gaps.
Inspection Procedure
1) Close the top cover or use an interlock cheat to home the machine.
2) Access holder to transfer in the service menu
Service Menu
Function Tests
Holder to Xfer
3) Check the gap between the holder face and the feeder.
4) If the faces are not parallel and have a gap between them or there is
a gap at the front or rear then adjustment is required.
Adjustment Procedure
1) If the mating faces are not touching access the HOLDER menu as
detailed in GP 6.3.17. If there is uneven contact between the faces go
to step 8).
Service Menu
Holder
2) Increase the HOLDER TO XFER value by 5.
3) Close the top cover or use and interlock cheat to home the machine.
4) Access the Service Menu and select Function Tests
Holder to Xfer.
5) Check the gap between the holder face and the feeder.
6) Repeat steps 2 through 5 until the mating faces are touching. If the
faces are touching across the whole length the adjustment is
complete. If not go to step 8).
7) If this procedure does not seem to reduce the gap then the holder
could be bouncing off the feeder at contact. Try reducing the value to
its minimum value (-100) and increasing from there.
8) If the faces are not touching across the complete length then the
feeder drawer angle can be adjusted.
9) Close the top cover or use an interlock cheat to home the machine.
10) Open the element feeder drawer and loosen the location pin at the
back enough so the pin can slide freely in the slot.
11) Loosen the 2 screws on the upper rail from underneath and the 4
screws on the lower rail. The middle slide rail may need to be moved
by hand to access all 4 screws on the lower rail.
12) Slide the feeder drawer back in.
Summary of Contents for StreamWire
