Reverse Function
CD and Credit Card Shredding
Rare Occasions of Jamming
Bin Full
Over Heating
Shredder Control Panel
Operation
Reverse
Forward
Auto
Safety First
This means you should be careful because long hair can
become entangled in the cutting head. This could hurt you.
This means don’t reach into the feed opening of the cutting
head. This could hurt you.
This means be careful of ties and other loose clothing which
could become entangled in the cutting head. This could hurt you.
This means keep children away from shredder.
This means do not use aerosol sprays anywhere near the unit.
This means be careful of loose jewelry which could become
entangeld in the cutting head.
Only insert 1 credit card or CD at a time (and shred inside
folded paper).
Connect shredder to mains supply
Ensure the on/off button (b) on the back of the machine is in the
on position.
To commence shredding, press the central Auto button (c). This
will illuminate the Anti-jam indicator. This sets the shredder into
auto mode and initiates the Mercury Anti-jam mechanism. The
standby symbol will illuminate blue and the Anti-jam indicator
will glow green. You are now able to shred.
Insert paper to be shredded into the feed area. The Mercury anti
jam mechanism will sense the thickness of the paper being
shredded.
Make sure the paper to be inserted is neatly stacked. Splayed
sheets can affect the operation of the anti-jam mechanism.
If the paper thickness is within the shredders capacity, the
motor will start and your documents will be shredded. Cutters
will stop once the shredding process is complete.
If the paper thickness is greater than the shredders sheet
capacity the anti-jam indicator will turn from green to red and
the motor will not run.
If this happens, remove some of the sheets from the paper
stack and re-try until the anti-jam indicator reverts back to
green, the shredder will then automatically start and allow the
paper to be shredded.
If the shredder is left in auto mode for more than 2 minutes
without being used, the shredder will automatically switch off in
order to save power.
Should you wish to reverse the shredding direction whilst
TISFEEJOHBEPDVNFOUBSFWFSTFCVUUPO EIBTCFFOmUUFEGPS
your convenience.
By pressing the reverse button the shredding cutters will
change direction allowing the retrieval of the document being
shredded. The anti-jam indicator will turn to red.
The reverse function will only run whilst the button is being
pressed.When the reverse button has been released the
shredder will revert to stand by mode.
The Mercury models can also shred CD’s and Credit Cards.
Switch shredder to auto mode and place credit card into the
centre of the marking for the credit card on the feed chute
Switch the shredder to auto mode and place CD into the
centre of the marking for the CD on the feedchute.
Only insert 1 credit card or CD at a time (and shred inside
folded paper).
In the unlikely event of the shredder jamming, use the reverse
function to unblock the shredder. (see Reverse function section)
Alternating between the reverse function and the forward run
will help unblock the feed area. To trigger the permanent
forward run mechanism, press Auto/On button down for
2 seconds.
Once the jam is clear, press the right hand auto button once to
revert back to auto mode. You can now resume shredding as
normal.
When the bin is full the shredder will not function and the bin full
symbol will illuminate red.
When this happens you must empty the bin.
t1VMMPVUUIFCJOUPFNQUZ
If the bin is not relocated correctly, the anti-jam indicator will
continue to glow red. Once relocated correctly the anti-jam
indicator will return to green.
If the shredder is used continuously for long periods of time the
shredder may overheat. If this occurs the thermometer symbol on
the indicator panel will flash blue.
When the shredder is ready to be used again the thermometer will
stop flashing and the anti-jam indicator will flash green once again.
To resume shredding press the auto button.