background image

3

Safety recommendations and warnings

 

 Warning! Carefully read the warnings below before using or working with the product!  

• 

Always adhere to local rules and regulations when installing or using the LED fixture.

• 

Do not open or disassemble the LED fixture; there are no serviceable parts inside. Opening or modifying the LED fixture 

can be dangerous and will void the warranty. 

• 

This product may cause interference to radio equipment and should not be installed near maritime safety communications 

equipment or other critical navigation or communication equipment operating between 0.45-30 MHz.

• 

Do not use the LED fixture when either the LED fixture or its power cord are damaged. Replace the power cord only 

with original, certified cords. 

• 

Modifications to the cords can lead to unwanted electromagnetic effects, which makes the product not comply with 

legal requirements.

• 

Do not expose the LED fixture to:

 

- (ambient) temperatures outside the specified range;

 

- dust and contamination;

 

- direct sunlight during use or HID light that could heat up the fixture.

• 

Always disconnect the LED fixture from mains before performing any maintenance. 

• 

Always allow for a cool-down period of at least 30 minutes before touching the LED. Touching the LED when the fixture is 

lit or immediately afterward can result in severe burns!   

• 

Do not use the LED fixture near flammable, explosive or reactive substances. Do not use sulfur vaporizers.  

• 

The installation and use of the LED fixture is the responsibility of the end user. Incorrect use or installation can lead 

to failure and damage to the LED fixture. Damage to the LED fixture and electronic circuitry as a result of incorrect 

installation and use voids the warranty.

• 

The minimum distance between adjacent lighting equipment is 4 inches (10.16 cm).  The minimum distance between lighting 

equipment and combustible materials is 4 inches (10.16 cm).

Contents (1)

A. 

Gavita CT 1930e LED

B. 

Mounting brackets (2x)

C. 

1-5/8" Unistrut Hanger

D. 

Safety wire

 (

Power cord sold separately).

Controls, connections 

and indications (2)

A. 

Wieland RST 16i5 male connector

B. 

Gavita 2xRJ45 connector

1. RJ IN

2. RJ OUT

C. 

Wieland RST 16i5 female connector

D. 

Assembled cable glands

E. 

Dummy Plug

A
C

D

E

B1

B2

A

B

C

D

2.   

1.   

Summary of Contents for CT 1930e









Reviews: