background image

S405.100 & S406.100 

USER GUIDE

Appendix | 61

7.4 EXCLUSIVE ONE-YEAR LIMITED WARRANTY   

Gaumard warrants that if the accompanying Gaumard product proves to be defective in material 

or workmanship within one year from the date on which the product is shipped from Gaumard to 

the customer, Gaumard will, at Gaumard’s option, repair or replace the Gaumard product.

This limited warranty covers all defects in material and workmanship in the Gaumard product, except:

 

»

Damage resulting from accident, misuse, abuse, neglect, or unintended use of the Gaumard product;

 

»

Damage resulting from failure to properly maintain the Gaumard product in accordance with 

Gaumard product instructions, including failure to properly clean the Gaumard product;

 

»

Damage resulting from a repair or attempted repair of the Gaumard product 

by anyone other than Gaumard or a Gaumard representative.

This one-year limited warranty is the sole and exclusive warranty provided by Gaumard for the accompanying 

Gaumard product, and Gaumard hereby explicitly disclaims the implied warranties of merchantability, 

satisfactory quality, and fitness for a particular purpose.

 Except for the limited obligations specifically 

set forth in this one-year limited warranty, Gaumard will not be liable for any direct, indirect, special, 

incidental, or consequential damages, whether based on contract, tort, or any other legal theory regardless 

of whether Gaumard has been advised of the possibilities of such damages. Some jurisdictions do not 

allow disclaimers of implied warranties or the exclusion or limitation of consequential damages, so the 

above disclaimers and exclusions may not apply and the first purchaser may have other legal rights.

This limited warranty applies only to the first purchaser of the product and is not transferable.

 Any subsequent 

purchasers or users of the product acquire the product “as is” and this limited warranty does not apply.

This limited warranty applies only to the products manufactured and produced by Gaumard

. This limited 

warranty does not apply to any products provided along with the Gaumard product that are manufactured by 

third parties. For example, third-party products such as computers (desktop, laptop, tablet, or handheld) and 

monitors (standard or touch-screen) are not covered by this limited warranty. However, third-party products 

are covered by the warranties provided by the respective third-party manufacturers and such warranties 

are transferred from Gaumard to purchaser upon purchase of the Gaumard product. Defects in third-party 

products are covered exclusively by the warranties provided by the third-parties. Gaumard does not provide 

any warranty, express or implied, with respect to any third-party products. Please contact the third-party 

manufacturer for information regarding the availability of extended warranties for third-party products.

Any waiver or amendment of this warranty must be in writing and signed by an officer of Gaumard.

 

»

In the event of a perceived defect in material or workmanship of 

the Gaumard product, the first purchaser must:

 

»

Contact Gaumard and request authorization to return the Gaumard product. Do NOT return the

 

»

Gaumard product to Gaumard without prior authorization.

 

»

Upon receiving authorization from Gaumard, send the Gaumard product along 

with copies of (1) the original bill of sale or receipt and (2) this limited warranty 

document to Gaumard at 14700 SW 136 Street, Miami, FL, 33196-5691 USA.

If the necessary repairs to the Gaumard product are covered by this limited warranty, then the first 

purchaser will pay only the incidental expenses associated with the repair, including any shipping, 

handling, and related costs for sending the product to Gaumard and for sending the product back 

to the first purchaser. However, if the repairs are not covered by this limited warranty, then the first 

purchaser will be liable for all repair costs in addition to costs of shipping and handling.

Extended Warranty 

 

In addition to the standard one year of coverage we offer a range of service plans through our Gaumard Cares 
program. For more information about Gaumard Cares service planes please contact customer service.

Summary of Contents for S405.100































































Reviews: