6
GAUI
TAI SHIH HOBBY CORPORATION
GAUI
TAI SHIH HOBBY CORPORATION
4
組裝代號說明
規格資料
非 常 注 意 : 組裝過程中請非常注意並
小心安裝及再確認組裝無誤。
注 意: 組裝過程中請注意並小心安裝。
危 險: 組裝過程中請小心安裝並注意
此危險程度可能造成安全性漏洞
導致人為傷害。
一般型止鬆劑
鎖緊螺絲並確認上膠
使用瞬間黏著劑
一般型止鬆劑
務必鎖緊螺絲並確認上膠
Symbols for Assembly Notices
Apply general thread lock.
To tight screw and apply thread lock.
Apply special thread lock.
To tight screw and apply thread lock.
Attention: Pay attention, care should be taken
during assembly.
Extreme attention:
More attention should be taken during assembly.
Double check after assembly.
Danger:
High level of attention should be taken during
assembly.
Action during assembly might be hazardous.
Extreme care should be taken to avoid injury.
Apply general thread lock.
Be certain to tight screw and
apply thread lock.
Apply special thread lock.
Be certain to tight screw and
apply thread lock.
Apply CA glue
Apply lubricant
Apply special thread lock
Specification
注 意:更改動力系統請注意電池電壓，馬達KV值及減速比 的關係來做搭配。
特殊型止鬆劑
務必鎖緊螺絲並確認上膠
特殊型止鬆劑
鎖緊螺絲並確認上膠
依個人需求使用潤滑油。
B-Bearing
B-
軸承
B(Dia.in)x(Dia.out)x(Thickness)
B(內徑)X(外徑)X(厚度)
Ø-TapScrew
Ø-
粗牙螺絲
Ø(Dia.out)x(Length)
Ø(外徑)X(長度)
M-Machine Screw
M-公制螺絲
M(Dia.out)x(Length)
M(外徑)X(長度)
P-tube
P-柱狀體
P(Dia.in)x(Dia.out)x(Length)
P(內徑)X(外徑)X(長度)
Pillar
P-柱狀體
P(Dia.out)x(Length)
P(外徑)X(長度)X(實心柱)
N-Nut
N-螺母
N(Dia.in)x(Width) L-Lock nut
N(外徑)X(長度)
W-Washer
W-
華司
W(Dia.in)xDia.out)x(Thickness)
W(內徑)X(外徑)X(厚度)
Gear Ratio 齒輪傳動比: 7.5 : 1 : 4.07 (E.M.T)
Overall Length (with Canopy):1000Specifications
機身長度(含艙罩):1000 mm
Main Rotor Diameter:1120mm
主旋翼迴轉直徑:1120 mm
Main rotor blades:500 ~ 530mm
主旋翼長度:500 ~530mm
Overall Height:323mm
機身高度:323 mm
Overall Width:165mm
機身寬度:165 mm
Tail Blade Length:82mm
尾旋翼葉片長度:82 mm
Tail Rotor Diameter:230mm
尾旋翼迴轉直徑:230 mm
Flying duration: 4~5 minutes
飛行時間:4~5分鐘
Power System(Recommanded):
Motor -- 910KV
ESC 100A ESC
6S1P(22.2v/4200mah)
動力系統(原廠建議):
馬達 910KV
電子變速器 100A ESC
使用鋰聚電池:6S1P(22.2v / 4200mah)
Total weight: 1850g ±3% (Equipped with Blades and
all electronic gears except Battery).
全配重量:1820g ±3% (全套含電子裝備不含電池)
Gear Ratio
齒輪傳動比列表
Standard Equipment
標準配備
13T Steel Pinion Gear (E.M.T) 9.2 : 1 : 4.07 = 2195 rpm
208786 - Steel Pinion Gear Pack(16T-for5.0mm shaft)
鋼製馬達齒16T(孔徑5.0mm)
14T Steel Pinion Gear (E.M.T) 8.6 : 1 : 4.07 = 2349 rpm
208903 - Rear Main Gear(61T)
61T齒輪
15T Steel Pinion Gear (E.M.T) 8 : 1 : 4.07 = 2525 rpm
208381 - Pulley Shaft with Steel Gear(15T)
皮帶齒軸附鋼齒(15T)
16T Steel Pinion Gear (E.M.T) 7.5 : 1 : 4.07 = 2693 rpm
208601 - (GUEC GM-601)Brushless Motor(1820W-910kv)
(GUEC GM-601)無刷馬達(1820W-910kv)
Tail rotor speed: 10960 rpm
208901 - 120T Main Gears
120T主齒盤
內徑較大
內徑較小
(L)
(S)
Bigger inner race
Smaller inner race
Main rotor speed 2693 rpm
Tail rotor speed 10960 rpm
內徑較大
內徑較小
(L)
(S)
Bigger inner race
Smaller inner race
以上圖示，於組裝時請確實注意，避免組裝後試飛造成失控零件
鬆脫等情況發生。
Make sure to assemble the parts as shown in figure above.
Incomplete or incorrect assembly may cause control failure during
flight.
Important:
The gear ratio, motor and battery should be set properly if the power system has been changed!!!
使用特殊型止鬆劑。
