background image

GAUI

P.17

GAUI 

TAI SHIH HOBBY CORPORATION 

電子變速器設定說明

三.選擇參數值:

馬達會循環鳴叫,在鳴叫某個提示音後將油門搖杆打到最高點,
則選擇該提示音所對應的設定值,接著鳴叫特殊提示音          
表示該參數值已被保存。
(此時如果不想再設定其他選項,則在2秒內將油門搖杆打到最低,
即可快速退出程式設定模式: 如果還要設定其他選項,則繼續等待,
退回第二步驟,再選擇其他設定選項)

一.進入程式設定模式:

 1. 開啟遙控器,將油門打到最高,電變接上電池。
 2. 等待2秒,馬達鳴叫 (嗶-嗶-) 提示音。
 3. 再等待5秒,馬達鳴叫           特殊提示音,
    表示已經進入設定模式。

使用遙控器油門搖杆設定參數分為四個步驟: 
一.進入程式設定              
二.選擇設定項            
三.選擇設定項下的參數值  
四.退出 

二. 選擇設定項:

進入程式設定模式後,會聽到8組鳴音,按如下順序循環鳴叫,
在鳴叫某組提示音後,3秒內將油門打到最低,則進入該設定項。

注:―長音“嗶——"相當於5聲短音“嗶-",所以在第二步
    {選擇設定項目}中,―長-短(嗶——嗶-)表示第為6選項。

使用遙控器進行參數設定的說明

四.退出設定:
   有如下兩種方式退出設定。

1. 在第三步驟,選擇設定值時,
   鳴叫特殊提示音        
   後,2秒內將油門打到最低點,
   則退出設定。

2. 在第二步驟,選擇設定選項時,
   當馬達鳴叫出代表第8設定
   選項的2長的鳴音後,
   3秒內將油門打到最低點,
   則退出設定。

煞車

(1短音)

電池類型

嗶-嗶-

(2短音)

低壓保護方式

嗶-嗶-嗶-

(3短音)

低壓保護閾值

嗶-嗶-嗶-嗶-

(4短音)

啟動模式

嗶——

(1長音)

進角

嗶——嗶-

(1長1短)

恢復出廠預設值

嗶——嗶-嗶-

(1長2短)

退出

嗶——嗶——

(2長)

設定選項

提示音

“嗶-"

1短音

“嗶-  嗶-"

2短音

“嗶- 嗶- 嗶-"

3短音

1.煞車

無煞車

2.電池類型

鋰電池

3.低壓保護方式 逐漸降低功率
4.低壓保護閾值

5.啟動模式

普通啟動

有煞車

鎳鎘/鎳氫電池

立即關閉功率

柔和啟動

超柔和啟動

6.進角

ESC  setting 

3. Set item value (Programmable value): 

You will hear several tones in loop. Set the value matching to  
a tone by moving throttle stick to top when you hear the tone,  
then a special tone “            ” emits, means the value is set and  
saved. (Keeping the throttle stick at top, you will go back to  
step 2 and you can select other items; Moving the stick to  
bottom within 2 seconds will exit program mode directly) 
 

1. Enter program mode 

a).Switch on transmitter, move throttle stick  
    to top , connect the battery pack to ESC  
b).Wait for 2 seconds, the motor should  
    emit special tone like “beep-beep-” 
c).Wait for another 5 seconds, special  
    tone like “              ” should be emitted,  
    which means program mode is entered. 

1.Enter program mode  
2.Select programmable items 
3.Set item’s value (Programmable value) 
4.Exit program mode  
 

2. Select programmable items:  

After entering program mode, you will hear 8 tones in a loop with the  
following sequence. If you move the throttle stick to bottom  
within 3 seconds after one kind of tones, this item will be selected. 

(1 short tone) 

(2 short tone)  

(3 short tone)  

(4 short tone) 

(1 long tone) 

(1 long 1 short) 

(1 long 2 short) 

(2 long tone) 

brake 

battery type 

cutoff mode  

cutoff threshold 

startup mode 

timing  

set all to default 

exit 

“beep” 

“beep-beep-” 

“beep-beep-beep-” 

“beep-beep-beep-beep-” 

“beep —” 

“beep — beep-” 

“beep — beep-beep-” 

“beep — beep—” 

Program the ESC with your transmitter (4 Steps): 

4. Exit program mode: 
There are 2 ways to exit  
program mode: 
1.In step 3, after special tone 
 “             ”, please  move throttle  
stick to the bottom position  
within 2 seconds. 
2.In step 2, after tone  
“beep 

— 

beep 

” 

(ie.The item #8), move throttle 
 stick to bottom within 3 seconds. 

Items 

Tones 

“beep-”  

1 short tone 

“beep-beep-”  

2 short tones 

“beep-beep-beep”  

3 short tones 

Brake 

Off 

Battery type 

Li-ion / Li-poly 

Cutoff mode 

Soft-Cut 

Cutoff threshold 

Low 

Start mode 

Normal 

Low 

On 

NiMH / NiCd 

Cut-Off 

Medium 

Soft 

Medium 

High 

Super soft 

High 

Timing 

Note: 1 long “beep-----” = 5 short “beep-”  
 

Summary of Contents for 500X





























Reviews: