background image

 
 

TWC562S TIRE CHANGER 

 
 
 

 

OPERATION 

This part of the operating instructions shows basic operation and use of control. All operators should know clearly the 

instruction before using the machine to prevent damaging machine and injured standby. 

Before carrying out any operation, deflate the tire and take off all the wheel balancing weights. 

 

The operation of the tire changer is divided into three parts: 

a)  BREAKING THE BEAD 

b)  TIRE DEMOUNTING 

c) 

TIRE MOUNTING

 

 

The turntable should be turn clockwise when foot pedal J pressed down, while rotate anticlockwise when pulled up. 

Note: If the turntable turns in the opposite direction to that shown, reverse two of the wires in the three-phase plug. 

 

Make sure that you have known clearly the functions of every foot pedals and other important parts: 

Pressing foot pedal J to run the turntable clockwise, while pulling up to run anticlockwise.   

 

Pressing the pedal (G) to tilt the arm; when the pedal is pressed again it returns to its 

normal position. 

 

Pressing the pedal (H) to opens the four jaws, the jaw holders will close again when 

pedal pressed again. 

 

Pressing the bead breaker pedal (I) to operate bead breaker, 

the breaker returns to its original position when pedal released.                                                         

FIG 4

 

The mounting head positions itself automatically at the correct distance from the rim. 

 

BREAKING THE BEAD   

When the bead breaker pedal is operated, the bead breaker arm moves quickly and powerfully. 

Anything within its range of action can be in danger of being crushed. 

 

•Check that the tire is deflated. If not, deflate it. 

•Close the turntable clamps completely 

•Use the rubber bead breaker protection to protect the wheel rim. 

Position the wheel against the rubber stops on the right side of the tire changer.   

•Position the bead breaker blade against the tire bead at a distance of about   

1 cm from the rim (fig.5). Pay attention to the blade, which must operate correctly   

onto the tire and not onto the rim. 

•Press down the pedal I to activate the bead breaker and release it when the blade   

has reached the end of its travel or in any case when the bead is broken. 

•Rotate the tire slightly and repeat the operation around the entire circumference of                                         

Fig 5

 

the rim and from both sides until the bead is completely detached from the rim

 

Summary of Contents for TWC-562S














Reviews: