manualshive.com logo in svg

GATEWORKS GW2342, Operating Manual

Share
Download
GATEWORKS GW2342 Operating Manual Download Page 20

Avila Network Computer Operating Manual 

 

20 of 25

 

2.7.  Getting Started 

The GW2342 is factory configured with Redboot v2.01 and a uCLinux port 
programmed into Flash memory. The software is configured to use either serial 
port for a serial console. To get started, connect a serial cable from to another 
computer running a terminal software application such as Windows 
HyperTerminal. Configure the terminal program for 115,200 baud, 8 data bits, 1 
stop bit, no parity and no flow control. Apply power and watch for Redboot and 
Linux output on the serial console. 
 
It is also possible to communicate to the GW2342 using a telnet session over 
Ethernet. First, connect the J10 Ethernet port on the GW2342 to the Ethernet 
port on a Host Computer using either a standard or a crossover cable. The 
default telnet address for the GW2342 is 192.168.3.2. Second, configure the 
Host Computer IP address to be on the same subnet (i.e. 192.168.3.99). Third, 
switch to Host Computer to a command prompt and type C:>telnet 192.168.3.2. 
The GW2342 console information will now be routed to the Host Computer 
display. 

2.8.  Manufactures Website Links / Support Mailing List 

The section provides links to hardware and software related web sites. An email 
mailing list is also available for Avila board support issues. To subscribe send an 
empty email to: 

[email protected]

 then confirm with a 

reply email. You can then post and view messages on the mailing list.  
 

Hardware 

 

Processor - Intel IXP420 and IXP425 

http://developer.intel.com/design/network/products/npfamily/ixp425.htm

 

Flash - Intel TE28F320J3, TE28F640J3, TE28F640J3 

http://developer.intel.com/design/flcomp/prodbref/298044.htm

 

Ethernet PHY - Intel LXT973 

http://developer.intel.com/design/network/products/lan/PHYs/lxt973.htm

 

Serial EEPROM - Philips Semiconductor PCF8594 

http://www.semiconductors.philips.com/

 

Real Time Clock - Dallas Semiconductor DS1672  

http://www.maxim-ic.com/

 

Temperature and Voltage Monitor - Analog Devices AD7418 

http://www.analog.com/

  

Fan Controller – Microchip TC653BEVUA 

http://www.microchip.com/

  

Summary of Contents for GW2342


























Reviews:

No comments

Brands by name

Popular brands

Load more brands