Gateway 930 series System Manual Download

Page: 70 / 160

Replacing and Adding System Components

Expansion cards

The server has six PCI expansion slots on the system board, that may be used
for a variety of expansion cards. These slots support four 64-bit PCI cards and
two 32-bit PCI cards.

Replacing an expansion card

To replace an expansion card:

Set any jumpers and switches on the replacement card. (See the card
instructions.)

Turn off the system and disconnect the power cord, modem cord (if
installed), and all external peripheral devices.

Observe all safety and static electricity precautions. (See “Preventing static
electricity discharge” on page 22.)

Remove the bezel. (See “Removing the bezel” on page 25.)

Remove the left side cover panel. (See “Removing the side cover panel”
on page 26.)

Disconnect any cables attached to the existing card.

8508088.book Page 62 Thursday, November 1, 2001 9:35 AM

Summary of Contents for 930 series

































































































































































Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands

Gateway 930 series, System Manual

Search results

Summary of Contents for 930 series

Reviews:

Related manuals for 930 series

Brands by name

Popular brands