Gateway 930 series System Manual Download | Manualshive

Page: 50 / 160

background image

42

Replacing and Adding System Components

Adding a hot-plug drive

The hot-plug drives are located at the bottom of the front panel. The hot-plug
bay supports up to six 1-inch high 3.5-inch SCA LVD SCSI hard drives.

The hot-plug drives are assigned SCSI ID numbers by the hot-plug backplane
with the drive at the far left side of the hot-plug bay assigned SCSI ID 0. The
backplane assigns SCSI IDs to the other drives in order up to SCSI ID 5 at the
far right side of the hot-plug bay. Install drives left to right.

Purchase additional SCSI drives through your Gateway sales representative.
Specify the system into which you will install the drive to ensure that the
correct drive and carrier are delivered.

Important

Gateway tests and verifies the operation and compatibility
of the drives it sells. Especially in a hot-plug or
mission-critical environment, additional or replacement
drives must conform to Gateway standards.

SCSI ID 0
SCSI ID 1
SCSI ID 2
SCSI ID 3
SCSI ID 4
SCSI ID 5

8508088.book Page 42 Thursday, November 1, 2001 9:35 AM

«
...
48
49
50
51
52
...
»

Summary of Contents for 930 series

































































































































































Reviews:

No comments

Related manuals for 930 series

BladeCenter HS22

Brand: IBM Pages: 18

Express5800/T110g-S

Brand: NEC Pages: 34

UniServer T1100 G3

Brand: H3C Pages: 66

UniServer R6900 G3

Brand: H3C Pages: 214

UniServer R6700 G3

Brand: H3C Pages: 151

UniServer R4900 G5

Brand: H3C Pages: 16

SUPERO SuperServer 1018L-MP

Brand: Supermicro Pages: 104

NPort P5250A Series

Brand: Moxa Technologies Pages: 2

Brand: Thecus Pages: 120

88643RU - System x3850 - 8864

Brand: IBM Pages: 192

Brand: AXIOMTEK Pages: 76

Brand: Xblue Networks Pages: 2

376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch

Brand: HP Pages: 169

Brand: MO-SYS Pages: 26

Brand: Tiger Technology Pages: 29

Brand: CasaTunes Pages: 7

Brand: XtendLan Pages: 38

SC835BTQ - R1K28B

Brand: Supero Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands