Gater WYZ34FS600V Operator'S Manual Download Page 15

 
 

15 

 

 

(3) Any warranted part that is scheduled for replacement as required maintenance in the written 

instructions must be warranted for the period of time prior to the first scheduled replacement point for that 
part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced by 
Worldlawn Power Equipment. Any such part repaired or replaced under warranty must be warranted for a 
time not less than the remainder of the period prior to the first scheduled replacement point for the part. 
 

(4) Repair or replacement of any warranted part under the warranty provisions of this article' must 

be performed at no charge to the owner at a warranty station. 
 

(5) Notwithstanding the provisions of subsection (4) above, warranty services or repairs must be 

provided at distribution centers that are franchised to service the subject engines or equipment. 
 

(6) The owner must not be charged for diagnostic labor that leads to the determination that a 

warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station. 
 

(7) Throughout the evaporative emission control system's warranty period set out in subsection 

(b)(2), Worldlawn Power Equipment must maintain a supply of warranted parts sufficient to meet the 
expected demand for such parts. 
 

(8) Manufacturer approved replacement parts must be used in the performance of any warranty 

maintenance or repairs and must be provided without charge to the owner. Such use will not reduce the 
warranty obligations of the manufacturer issuing the warranty. 
 

(9) The use of any add-on or modified parts will be grounds for disallowing a warranty claim made 

in accordance with this article. Worldlawn Power Equipment will not be liable under this Article to warrant 
failures of warranted parts caused by the use of an add-on or modified part. 
 

(10) Worldlawn Power Equipment shall provide any documents that describe the warranty 

procedures or policies within five working days of request by the Air Resources Board. 
 
EMISSION WARRANTY PARTS LIST: 
1) Fuel Tank, 2) Fuel line, 3) Fuel cap, 4) remote vent, 5) Carbon canister 
 

Written instructions for the maintenance and use of the evaporative emissions control system by the 

owner shall be furnished with each new engine or equipment 

 

 

Summary of Contents for WYZ34FS600V





















Reviews: