EN
EN
12
13
BOIL-DRY PROTECTION
When the filling level is too low, the heating cylcle may be terminated prematurely
and unusual large amounts of steam may escape from the spout. Maybe a bubbling
noise is heard. In this case, add a sufficient amount of water—at least 200ml.
When the boil-dry protection has been triggered, “E3” is shown on the display. In
this case, switch off the base via the “ON/OFF” button, remove the kettle, open the
lid and wait for approx. 15 minutes. Thereafter you may use the kettle again quite
normally.
IMPORTANT -
For preserving a long lifetime of the kettle, avoid leaving the kettle
run dry. However, when this happened exceptionally, we strongly advice to avo-
id pouring cold water immediately onto the overheated heating plate. Leave the
kettle cool down first. Always ensure that there are always at least 200ml of water
in the kettle, during operation. Especially, when keeping the water warm at high
temperature for a prolonged time, intermediately contol the filling level and add
water in time.
BEFORE FIRST USE
WARNING
–
DO NOT let children play with the appliance, or any part
of it, or the packaging!
Do not leave the appliance unattended, when it is in
reach of children younger than 8 years and animals. Always unplug the power
base, before cleaning.
Do not immerse the power base, power cord, or kettle
in water or other liquids or pour any liquids on these parts.
Do not place the
appliance or any part of it in an automatic dishwasher.
1. Unpack the appliance and all accessories carefully. Check that no parts are
damaged or missing (see: ‘Knowing Your Water Kettle’). Carefully remove all
shipping materials and promotional materials. However, do not remove the
model label at the bottom of the power base or kettle.
2. Before first use and after a prolonged period of storage, thoroughly rinse the
interior of the kettle. Then fill the kettle with 1 litre clear, cold tap water up to
the “MAX / 1.0L” marking.
3. Let the kettle heat the water via the “Boil” button until the heating cycle is termi-
nated automatically (see: ‘Operation’). Discard the water and rinse the interior
of the kettle again. Thereafter, the kettle is ready for use.
OPERATION
WARNING
– Do not leave the appliance unattended, while it is connected
to the power supply. Ensure that the filling level is between 200ml and 1000ml.
When the kettle is overfilled, large amounts of hot water may splash out. Only fill
in clear drinking water. Do not heat any food or foreign objects via the appliance.
During operation and some time thereafter as well as during pouring, hot steam
and some splashes of hot water may escape. Even the exterior of the kettle may
get hot. Only touch the kettle and lid at the handle, while they may be hot. If there
are any liquids running out during operation, immediately unplug the power base
and remove the kettle from the power base.
IMPORTANT -
When heating hard water, scale will accumulate at the interior of
the kettle. Deposits of scale may cause overheating and excessive energy loss.
Clean and descale the kettle regularly (see: ‘Care and Cleaning’).
IMPORTANT -
Always close the lid for operation. With the lid open, the automa-
tic shut-off may not operate properly due to high energy loss. Possibly, the heating
cycle will not be terminated at all.
1. Remove the kettle from the power base and pull out the lid. Fill the kettle with the
required amount of drinking water (200-1000 ml; filling level “MIN / 0.2L” to
“MAX / 1.0L”, approx. 1 inch below the upper rim). Close the lid. Ensure that
the exterior of the kettle is dry.
2. Unwind the power cord completely. Place the kettle onto the power base. Con-
nect the appliance to the power supply. The ON/OFF button illuminates.
3. Press the ON/OFF button. All buttons and the actual temperature “Temp” and
preset temperature (“Set 40°C”) illuminate.
4.
Heating the water to the boil:
Press the “Boil” button. The kettle starts heating
immediately. The appliance will terminate the heating cycle automatically, when
100°C (212°F) is reached.
5.
Heating the water to a preset temperature:
Press the adjustment button (“+”
or “–”), until the desired temperature is shown on the display (40-99 °C; 104-
210°F). Approx. 4 seconds after your last entry, the set temperature starts flas-
hing and the kettle starts heating the water. As soon as the set temperature is
reached, a beep sounds and the heating cycle is terminated automatically.
NOTE
When keeping the buttons pressed, the temperature on the display runs on until
you release the button. You can change the set temperature via the adjustment
buttons, whenever you like—even during operation.
